Asus Pundit-PH3 Pundit-PH3 User''s Manual for English - Page 55

Connectors

Get Asus Pundit-PH3 PDF manuals and user guides View all Asus Pundit-PH3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

4.3 Connectors 4.3.1 Rear panel connectors Refer to section "1.3 Rear panel" for a description of the rear panel I/O ports. 4.3.2 Internal connectors 1 . Primary IDE connector (40-1 pin PRI_IDE1) This connector is for an Ultra DMA 100/66 signal cable. The Ultra DMA 100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66 IDE master device (hard disk drive). If you install an optical drive and an IDE HDD, you must configure the optical drive as a slave device by setting its jumper accordingly. Refer to the optical drive or HDD documentation for the jumper settings. • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices. ® IDE connector PRI_IDE1 NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. PIN 1 ASUS Pundit-PH3 4-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
4-5
4-5
4-5
4-5
4-5
ASUS Pundit-PH3
ASUS Pundit-PH3
ASUS Pundit-PH3
ASUS Pundit-PH3
ASUS Pundit-PH3
4.3
Connectors
4.3.1
4.3.1
4.3.1
4.3.1
4.3.1
Rear panel connectors
Rear panel connectors
Rear panel connectors
Rear panel connectors
Rear panel connectors
Refer to section
“
1.3 Rear panel
”
for a description of the rear panel I/O ports.
4.3.2
4.3.2
4.3.2
4.3.2
4.3.2
Internal connectors
Internal connectors
Internal connectors
Internal connectors
Internal connectors
1.
1.
1.
1.
1.
Primary IDE connector (40-1 pin PRI_IDE1)
Primary IDE connector (40-1 pin PRI_IDE1)
Primary IDE connector (40-1 pin PRI_IDE1)
Primary IDE connector (40-1 pin PRI_IDE1)
Primary IDE connector (40-1 pin PRI_IDE1)
This connector is for an Ultra DMA 100/66 signal cable. The Ultra
DMA 100/66 signal cable has three connectors: a blue connector for
the primary IDE connector on the motherboard, a black connector for
an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive),
and a gray connector for an Ultra DMA 100/66 IDE master device (hard
disk drive). If you install an optical drive and an IDE HDD, you must
configure the optical drive as a slave device by setting its jumper
accordingly. Refer to the optical drive or HDD documentation for the
jumper settings.
•
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
IDE connector
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
PRI_IDE1
PIN 1