Asus ROG STRIX B250F GAMING STRIX B250F GAMING Users ManualEnglish - Page 70

APM Configuration, 3.6.9 Network Stack Configuration, 3.6.10 HDD/SSD SMART Information

Get Asus ROG STRIX B250F GAMING PDF manuals and user guides View all Asus ROG STRIX B250F GAMING manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

PCIEX16_2 Configuration [Auto] This item allows you to configure the PCIe x16_2 device settings. [Auto] Automatically detects the device installed. (1) When a device is installed in PCIe x1_2 or PCIEx1_3 slot, PCIe x16_2 only runs in X2 Mode. (2) When there are no devices installed in PCIe x1_2 or PCIe x1_3 slot, PCIe x16_2 can run in X4 Mode. [X2 Mode] PCIe x16_2 only runs in X2 Mode. PCIe x1_2 and PCIe x1_3 are enabled. [X4 Mode] PCIe x16_2 can run in X4 Mode. PCIe x1_2 and PCIe x1_3 are disabled. RGB LED Lighting [On] [On] The LEDs will always light up at the S0(Working), S3(Sleep), and S5(Soft off) states, but not light up at the S4/S5 state when the ErP Ready item is enabled. [Off] The LEDs will not light up. Intel LAN Controller [Enabled] [Enabled] Enables the Intel LAN controller. [Disabled] Disables the controller. Serial Port Configuration The sub-items in this menu allow you to set the serial port configuration. 3.6.8 APM Configuration ErP Ready [Disabled] Allows BIOS to switch off some power at S5 to get the system ready for ErP requirement. When set to [Enabled], all other PME options will be switched off. Configuration options: [Enable(S4+S5)] [Enable(S5)] [Disabled] 3.6.9 Network Stack Configuration The items in this menu allow you to configure Ipv4 / Ipv6 PXE support. 3.6.10 HDD/SSD SMART Information This menu displays the SMART information of the connected devices. 3.6.11 USB Configuration The items in this menu allow you to change the USB-related features. The USB Devices item shows the auto-detected values. If no USB device is detected, the item shows None. USB Single Port Control This item allows you to enable or disable the individual USB ports. Refer to section 1.1.2 Motherboard layout for the location of the USB ports. Chapter 3 3-14 Chapter 3: BIOS Setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
3-14
Chapter 3: BIOS Setup
Chapter 3
PCIEX16_2 Configuration [Auto]
This item allows you to configure the PCIe x16_2 device settings.
[Auto]
Automatically detects the device installed.
(1)
When a device is installed in PCIe x1_2 or PCIEx1_3 slot, PCIe x16_2
only runs in X2 Mode.
(2)
When there are no devices installed in PCIe x1_2 or PCIe x1_3 slot,
PCIe x16_2 can run in X4 Mode.
[X2 Mode]
PCIe x16_2 only runs in X2 Mode. PCIe x1_2 and PCIe x1_3 are enabled.
[X4 Mode]
PCIe x16_2 can run in X4 Mode. PCIe x1_2 and PCIe x1_3 are disabled.
RGB LED Lighting [On]
[On]
The LEDs will always light up at the S0(Working), S3(Sleep), and S5(Soft
off) states, but not light up at the S4/S5 state when the ErP Ready item is
enabled.
[Off]
The LEDs will not light up.
Intel LAN Controller [Enabled]
[Enabled]
Enables the Intel LAN controller.
[Disabled]
Disables the controller.
Serial Port Configuration
The sub-items in this menu allow you to set the serial port configuration.
3.6.8
APM Configuration
ErP Ready [Disabled]
Allows BIOS to switch off some power at S5 to get the system ready for ErP requirement.
When set to [Enabled], all other PME options will be switched off.
Configuration options: [Enable(S4+S5)] [Enable(S5)] [Disabled]
3.6.9
Network Stack Configuration
The items in this menu allow you to configure Ipv4 / Ipv6 PXE support.
3.6.10
HDD/SSD SMART Information
This menu displays the SMART information of the connected devices.
3.6.11
USB Configuration
The items in this menu allow you to change the USB-related features.
The
USB Devices
item shows the auto-detected values. If no USB device is detected, the
item shows
None
.
USB Single Port Control
This item allows you to enable or disable the individual USB ports.
Refer to section
1.1.2 Motherboard layout
for the location of the USB ports.