Asus RS100-E6 PI2 User Manual - Page 32

Optical disk drive ODD, a power plug from the power supply

Get Asus RS100-E6 PI2 PDF manuals and user guides View all Asus RS100-E6 PI2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

3. Insert the hard disk drive into the HDD bracket and secure it with four screws. 4. Connect the SATA signal cable and a power plug from the power supply to the hard disk drive. Use the L-type SATA connector to connect to the hard disk drive. L-type SATA connector 5. Place the HDD bracket with the hard disk drive installed into the HDD tray 2, matching the four screw holes. Then, secure the HDD bracket with four screws. Power plug SATA signal cable 6. Refer to section 2.7.2 Optical disk drive (ODD) to reinstall the ODD. 2-14 Chapter 2: Hardware setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
Chapter 2:
Hardware setup
2-14
3.
Insert the hard disk drive into the
HDD bracket and secure it with four
screws.
5.
Place the HDD bracket with the
hard disk drive installed into the
HDD tray 2, matching the four
screw holes. Then, secure the HDD
bracket with four screws.
4.
Connect the SATA signal cable and
a power plug from the power supply
to the hard disk drive.
L-type SATA
connector
Use the L-type SATA connector
to connect to the hard disk drive.
6.
Refer to section
2.7.2 Optical disk drive (ODD)
to reinstall the ODD.
Power plug
SATA signal cable