Asus RS120-E5 PA2 User Guide - Page 103

Installing hard disk drives, Setting the RAID item in BIOS

Get Asus RS120-E5 PA2 PDF manuals and user guides View all Asus RS120-E5 PA2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

6.1.2 Installing hard disk drives The motherboard supports Serial ATA for RAID set configuration. For optimal performance, install identical drives of the same model and capacity when creating a disk array. To install the SATA hard disks for RAID configuration: 1. Install the SATA hard disks into the drive bays following the instructions in the system user guide. 2. Connect a SATA signal cable to the signal connector at the back of each drive and to the SATA connector on the motherboard. 3. Connect a SATA power cable to the power connector on each drive. 6.1.3 Setting the RAID item in BIOS You must set the RAID item in the BIOS Setup before you can create a RAID set from SATA hard disk drives attached to the SATA connectors supported by the Intel® 6321ESB Southbridge chip. To do this: 1. Enter the BIOS Setup during POST. 2. Go to the Main Menu > IDE Configuration > S-ATA Configuration, then press . 3. Set the SATA Controller Mode Option item to [Enhanced], then press . 4. Set the SATA RAID Enable item to [Enabled]. 5. Save your changes, then exit the BIOS Setup. Refer to Chapter 5 for details on entering and navigating through the BIOS Setup. 6.1.4 RAID configuration utilities Depending on the RAID connectors that you use, you can create a RAID set using the utilities embedded in each RAID controller. For example, use the LSI Logic Embedded SATA RAID Setup Utility or the Intel® Matrix Storage Manager if you installed Serial ATA hard disk drives on the Serial ATA connectors supported by the Intel® 6321ESB Southbridge. Refer to the succeeding sections for details on how to use each RAID configuration utility. ASUS RS120-E5/PA2 6-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
ASUS RS120-E5/PA2
6-3
6.1.2
Installing hard disk drives
The motherboard supports Serial ATA for RAID set configuration. For optimal
performance, install identical drives of the same model and capacity when creating
a disk array.
To install the SATA hard disks for RAID configuration:
1.
Install the SATA hard disks into the drive bays following the instructions in the
system user guide.
2.
Connect a SATA signal cable to the signal connector at the back of each drive
and to the SATA connector on the motherboard.
3.
Connect a SATA power cable to the power connector on each drive.
6.1.3
Setting the RAID item in BIOS
You must set the RAID item in the BIOS Setup before you can create a RAID set
from SATA hard disk drives attached to the SATA connectors supported by the
Intel
®
6321ESB Southbridge chip. To do this:
1.
Enter the BIOS Setup during POST.
2.
Go to the
Main Menu
>
IDE Configuration
>
S-ATA Configuration
, then
press <Enter>.
3.
Set the
SATA Controller Mode Option
item to [Enhanced], then press
<Enter>.
4.
Set the
SATA RAID Enable
item to [Enabled].
5.
Save your changes, then exit the BIOS Setup.
Refer to Chapter 5 for details on entering and navigating through the BIOS
Setup.
6.1.4
RAID configuration utilities
Depending on the RAID connectors that you use, you can create a RAID set using
the utilities embedded in each RAID controller. For example, use the
LSI Logic
Embedded SATA RAID Setup Utility
or the
Intel
®
Matrix Storage Manager
if you
installed Serial ATA hard disk drives on the Serial ATA connectors supported by the
Intel
®
6321ESB Southbridge.
Refer to the succeeding sections for details on how to use each RAID configuration
utility.