Asus TUF B450-PLUS GAMING Users Manual English - Page 12

AMD Serial ATA 6.0 Gb/s connectors 7-pin SATA6G_1~6, Aura RGB Strip header 4-pin - compatibility

Page 12 highlights

Aura RGB Strip header (4-pin RGB_HEADER) This header is for RGB LED strip. The RGB header supports 5050 RGB multi-color LED strips (12V/G/R/B), with a maximum power rating of 3A (12V), and no longer than 3 m. RGB_HEADER PIN 1 +12V G R B B R G 12V Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components. • Actual lighting and color will vary with LED strip. • If your LED strip does not light up, check if the RGB LED extension cable and the RGB LED strip is connected in the correct orientation, and the 12V connector is aligned with the 12V header on the motherboard. • The LED strip will only light up when the system is operating. • The LED strips are purchased separately. M.2 socket 3 This socket allows you to install M.2 (NGFF) SSD modules. • The M.2 socket supports PCIe 3.0 x4 mode and SATA mode M Key design and type 2242 / 2260 / 2280 / 22110 storage devices. • The M.2 Socket shares bandwidth with the SATA_5/6 ports, and therefore the SATA_5/6 ports cannot be used when an M.2 device is installed. M.2(SOCKET3) 22110 2280 2260 2242 AMD Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_1~6) These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0 Gb/s signal cables. System panel connector (20-5 pin F_PANEL) This connector supports several chassis-mounted functions. USB 3.1 Gen 1 (up to 5Gbps) connector (20-1 pin U31G1_12) Connect a USB 3.1 Gen 1 module to this connector for additional USB 3.1 Gen 1 front or rear panel ports. This connector complies with USB 3.1 Gen 1 specifications and provides faster data transfer speeds of up to 5 Gbps, faster charging time for USB-chargeable devices, optimized power efficiency, and backward compatibility with USB 2.0. USB 2.0 connectors (10-1 pin USB34,USB56) Connect a USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specifications and support up to 480Mbps connection speed. 1-3 ASUS TUF B450-PLUS GAMING

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30

ASUS TUF B450-PLUS GAMING
1-3
Aura RGB Strip header (4-pin
RGB_HEADER)
This header is for RGB LED strip.
12V
G
R
B
RGB_HEADER
PIN 1
+12V G
R
B
The RGB header supports 5050
RGB multi-color LED strips
(12V/G/R/B), with a maximum
power rating of 3A (12V), and no
longer than 3 m.
Before you install or remove any component, ensure that the ATX power supply is
switched off or the power cord is detached from the power supply. Failure to do so may
cause severe damage to the motherboard, peripherals, or components.
Actual lighting and color will vary with LED strip.
If your LED strip does not light up, check if the RGB LED extension cable and the
RGB LED strip is connected in the correct orientation, and the 12V connector is
aligned with the 12V header on the motherboard.
The LED strip will only light up when the system is operating.
The LED strips are purchased separately.
M.2 socket 3
This socket allows you to install M.2 (NGFF) SSD
modules.
M.2(SOCKET3)
2280
22110
2260
2242
The M.2 socket supports PCIe 3.0 x4 mode and SATA
mode M Key design and type 2242 / 2260 / 2280 /
22110 storage devices.
The M.2 Socket shares bandwidth with the SATA_5/6
ports, and therefore the SATA_5/6 ports cannot be
used when an M.2 device is installed.
AMD Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_1~6)
These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA
6.0 Gb/s signal cables.
System panel connector (20-5 pin F_PANEL)
This connector supports several chassis-mounted functions.
USB 3.1 Gen 1 (up to 5Gbps) connector (20-1 pin U31G1_12)
Connect a USB 3.1 Gen 1 module to this connector for additional USB 3.1
Gen 1 front or rear panel ports. This connector complies with USB 3.1 Gen 1
specifications and provides faster data transfer speeds of up to 5 Gbps, faster
charging time for USB-chargeable devices, optimized power efficiency, and
backward compatibility with USB 2.0.
USB 2.0 connectors (10-1 pin USB34,USB56)
Connect a USB module cable to any of these connectors, then install the module
to a slot opening at the back of the system chassis. These USB connectors comply
with USB 2.0 specifications and support up to 480Mbps connection speed.