Asus V4-P5G43 User Manual - Page 40

Installing a hard disk drive

Get Asus V4-P5G43 PDF manuals and user guides View all Asus V4-P5G43 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2.7.3 Installing a hard disk drive 1. Remove the 3.5-inch hard drive holder out of the chassis. The 3.5-inch hard drive holder is 3 optional. 3 2 2. Insert the hard disk drive to the 3.5-inch hard drive holder, then carefully push the drive until its screw holes align with the holes on the holder. 3. Secure the hard disk drive with two screws on both sides of the bay. 4. Replace the hard drive holder to the chassis and secure the screws. For SATA HDD: Connect the SATA SATA IDE signal and power plugs to the connectors at the back of the drive. For IDE HDD: Connect the IDE and power plugs to the connectors at the back of the drive. 2-22 Chapter 2: Basic installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
2-22
Chapter 2: Basic installation
2.7.3
Installing a hard disk drive
1.
Remove the 3.5-inch hard drive holder
out of the chassis.
2
3
3
2.
Insert the hard disk drive to the 3.5-inch hard drive holder, then carefully push
the drive until its screw holes align with the holes on the holder.
3.
Secure the hard disk drive with two screws on both sides of the bay.
4.
Replace the hard drive holder to the chassis and secure the screws.
The 3.5-inch hard drive holder is
optional.
For SATA HDD: Connect the SATA
signal and power plugs to the
connectors at the back of the drive.
For IDE HDD: Connect the IDE and
power plugs to the connectors at the
back of the drive.
SATA
IDE