Asus p4spmx P4SP-MX User Manual - Page 26

Internal connectors

Get Asus p4spmx PDF manuals and user guides View all Asus p4spmx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

1.10.2 Internal connectors 1. IDE connectors (40-1 pin PRI_IDE1, SEC_IDE1) This connector supports the provided UltraDMA133 IDE hard disk ribbon cable. Connect the cable's blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraDMA133 slave device (hard disk drive) and the black connector to the UltraDMA133 master device. • Follow the hard disk drive documentation when setting the device in master or slave mode. • Pin 20 on each IDE connector is removed to match the covered hole on the UltraDMA cable connector. This prevents incorrect orientation when you connect the cables. • The hole near the blue connector on the UltraDMA cable is intentional. NOTE: Orient the red markings on the IDE ribbon cable to PIN 1 SEC_IDE1 PRI_IDE1 ® P4SP-MX P4SP-MX IDE Connectors PIN 1 PIN 1 2. Floppy disk drive connector (34-1 pin FLOPPY1) This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug). FLOPPY1 ® P4SP-MX PIN 1 NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. P4SP-MX Floppy Disk Drive Connector 1-18 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
1-18
Chapter 1: Product introduction
2.
Floppy disk drive connector (34-1 pin FLOPPY1)
This connector supports the provided floppy drive ribbon cable. After
connecting one end to the motherboard, connect the other end to the floppy
drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables
with pin 5 plug).
1.10.2
Internal connectors
1.
IDE connectors (40-1 pin PRI_IDE1, SEC_IDE1)
This connector supports the provided UltraDMA133 IDE hard disk ribbon cable.
Connect the cable
’
s blue connector to the primary (recommended) or secondary
IDE connector, then connect the gray connector to the UltraDMA133 slave
device (hard disk drive) and the black connector to the UltraDMA133 master
device.
•
Follow the hard disk drive documentation when setting the device in master
or slave mode.
•
Pin 20 on each IDE connector is removed to match the covered hole on the
UltraDMA cable connector. This prevents incorrect orientation when you
connect the cables.
•
The hole near the blue connector on the UltraDMA cable is intentional.
P4SP-MX
P4SP-MX IDE Connectors
NOTE:
Orient the red markings
on the IDE ribbon cable to
PIN 1
SEC_IDE1
PIN 1
PRI_IDE1
PIN 1
P4SP-MX
NOTE:
Orient the red markings on
the floppy ribbon cable to PIN 1.
P4SP-MX Floppy Disk Drive Connector
PIN 1
FLOPPY1