Audiovox DV1202 Owners Manual - Page 12

Component video outputs DVD, Progressive outputs DVD, Coaxial Antenna Jack - manual

Get Audiovox DV1202 PDF manuals and user guides View all Audiovox DV1202 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Setup or Component video outputs (DVD) Some TVs or monitors are equipped with component video inputs. Using the Audio cable (not supplied), connect the left/right AUDIO OUT jacks on your Unit to the left/right AUDIO IN jacks on your TV and the Component video cable (not supplied), connect the Green plug Y VIDEO OUT jack on your Unit to Y VIDEO IN jack on your TV, the Blue plug PB/CB VIDEO OUT jack on your Unit to PB/CB VIDEO IN jack on your TV and the Red plug PR/CR VIDEO OUT jack on your Unit to PR/CR VIDEO IN jack on your TV to view the higher quality picture playback. Progressive outputs (DVD) Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video signal. Using the Audio cable (not supplied), connect the left/right AUDIO OUT jacks on your Unit to the left/right AUDIO IN jacks on your TV and the Component video cable (not supplied), connect the Green plug Y VIDEO OUT jack on your Unit to Y VIDEO IN jack on your TV, the Blue plug PB/CB VIDEO OUT jack on your Unit to PB/CB VIDEO IN jack on your TV and the Red plug PR/CR VIDEO OUT jack on your Unit to PR/CR VIDEO IN jack on your TV to enjoy highest quality picture with less flicker. Press the SETUP button and select Video Output to YUV. Connect the component video cable to TV, press the P. SCAN button on the remote control when DVD is stopped. "P. SCAN" display. You can select the output signal for better picture quality. Attention: • When progressive output is activated, there is no video signal output from S-video and RCA (CVBS) video jacks. • Make sure your TV supports progressive scan component video signal, press the P. SCAN button repeatedly until "CVBS" is displayed to go back to CVBS video signal. FM ANT. 300Ω To Y VIDEO OUT To PB/CB VIDEO OUT To PR/CR VIDEO OUT Component video cable (not supplied) Audio cable (not supplied) (white) To wall outlet (red) To Y VIDEO IN To PB/CBVIDEO IN To PR/CRVIDEO IN or Coaxial Antenna Jack Some TVs do not have an RCA or S-Video jack, they only have a coaxial antenna jack. In order to connect this Unit to these TVs, you must purchase an RF modulator (availabel in teh Audio/Video department of most electronics retailers or at http://www.18002526123.com) and follow the instructions included with it. Notes : • Connect the Unit to your TV directly. If you connect the Unit through a VCR, the playback picture will be distorted because DVD discs are copy protected. • When you connect the Unit to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connection. • Refer to the instruction manual of the connected equipment as well. E-10-16.pmd E - 11 11 (continued to next page) 4/24/2004, 12:24 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
E - 11
Setup
(continued to next page)
or
Component video outputs (DVD)
Some TVs or monitors are equipped with component video inputs.
Using the Audio cable (not supplied), connect the left/right AUDIO OUT jacks on your Unit to the left/right AUDIO IN
jacks on your TV and the Component video cable (not supplied), connect the
Green
plug
Y
VIDEO OUT jack on your
Unit
to
Y
VIDEO IN jack on your TV, the
Blue
plug
P
B
/C
B
VIDEO OUT jack on your Unit to
P
B
/C
B
VIDEO IN jack on
your TV and the
Red
plug
P
R
/C
R
VIDEO OUT jack on your Unit to
P
R
/C
R
VIDEO IN jack on your TV to view the higher
quality picture playback.
Progressive outputs (DVD)
Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively
scanned video signal.
Using the Audio cable (not supplied), connect the left/right AUDIO OUT jacks on your Unit to the left/right AUDIO IN
jacks on your TV and the Component video cable (not supplied), connect the
Green
plug
Y
VIDEO OUT jack on your
Unit
to
Y
VIDEO IN jack on your TV, the
Blue
plug
P
B
/C
B
VIDEO OUT jack on your Unit to
P
B
/C
B
VIDEO IN jack on
your TV and the
Red
plug
P
R
/C
R
VIDEO OUT jack on your Unit to
P
R
/C
R
VIDEO IN jack on your TV to enjoy highest
quality picture with less flicker.
Press the
SETUP
button and select Video Output to YUV. Connect the component video cable to TV, press the
P.
SCAN
button on the remote control when DVD is stopped. "P. SCAN" display. You can select the output signal for
better picture quality.
Attention:
•
When progressive output is activated, there is no video signal output from S-video and RCA (CVBS) video jacks.
•
Make sure your TV supports progressive scan component video signal, press the
P. SCAN
button repeatedly until
"CVBS" is displayed to go back to CVBS video signal.
Notes :
•
Connect the Unit to your TV directly. If you connect the Unit through a VCR, the playback picture will be distorted
because DVD discs are copy protected.
•
When you connect the Unit to other equipment, be sure to turn off the power and unplug all of the equipment from
the wall outlet before making any connection.
•
Refer to the instruction manual of the connected equipment as well.
or
Coaxial Antenna Jack
Some TVs do not have an RCA or S-Video jack, they only have a coaxial antenna jack.
In order to connect this Unit
to these TVs, you must purchase an RF modulator (availabel in teh Audio/Video department of most electronics
retailers or at
) and follow the instructions included with it.
FM ANT.
300
Ω
To wall outlet
Audio cable
(not supplied)
(red)
(white)
Component video cable (not supplied)
To
VIDEO
OUT
Y
To
VIDEO
OUT
PR/CR
To
VIDEO
OUT
PB/CB
To VIDEO IN
Y
To
VIDEO IN
PR/CR
To
VIDEO IN
PB/CB
E-10-16.pmd
4/24/2004, 12:24 PM
11