Audiovox RP5120 User Manual - Page 1
Audiovox RP5120 Manual
View all Audiovox RP5120 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
v4.0 (EN/E) user manual manual de usuario RP5120 For your records In the event that service should be required, you may need the model number and the serial number. In the space below, record the date and place of purchase and the serial number: Model No.: Date of Purchase: Place of Purchase: Serial No.: RRCCAA DRTPA581020A Equipment tested for compliance as a complete unit This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la class B est conforme à la norme du NMB-003 du Canada. Power Supply • (battery power) 2 x "AAA" ESD Remark: In case of misfunction due to electrostatic discharge just reset the product (disconnect and reconnect of the power source may be required) to resume normal operation. EN/E It is important to read this instruction prior to using your new product for the first time. Es importante leer este manual antes de usar por vez primera su equipo. WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FCC information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Service information This product should be serviced only by those specially trained in appropriate servicing techniques. For instructions on how to obtain service, refer to the warranty included in this user manual. Maintenance Clean the unit with a soft cloth, or a damp chamois leather. Never use solvents. Precautions for the unit • Do not use the unit immediately after transportation from a cold place to a warm place; condensation problem may be resulted. • Avoid shock to the unit especially during recording. Recorded data can be damaged. • Do not store the unit near fire, places with high temperature or places with direct sunlight. • Do not operate or store unit in places with frequent static electricity or electrical noise (e.g. speaker, TV set). • Clean the unit with a soft cloth or a damp chamois leather. Never use solvents. • The unit must only be opened by qualified personnel. • Do not expose this appliance to rain or moisture. Important battery precautions • Any battery may present a risk of fire, explosion, or chemical burn if abused. Do not try to charge a battery that is not intended to be recharged, do not incinerate, and do not puncture. • Non-rechargeable batteries, such as alkaline batteries, may leak if left in your product for a long period of time. Remove the batteries from the product if you are not going to use it for a month or more. • If your product uses more than one battery, do not mix types and make sure they are inserted correctly. Mixing types or inserting incorrectly may cause them to leak. • Discard any leaky or deformed battery immediately. They may cause skin burns or other personal injury. • Please help to protect the environment by recycling or disposing of batteries according to federal, state, and local regulations. Before you begin Unpacking your player You should have the following: • one voice recorder • one USB cable • one user manual • one quick start guide Installing batteries This player can be operated by 2 "AAA" batteries (not included). 1. Slide the battery compartment door to open. 2. Insert the two supplied "AAA" batteries with polarities matching indications. 3. Replace the battery compartment door. Refer to the battery level indicator on display for batteries level. Replace with new batteries when the indicator is empty. Turn off the player first before replacing batteries. If power interruption exceeds 20 seconds, date and time have to be set again. Auto power shut down The player will be automatically turned off if left idle for three minutes. Using earphones and external microphone • When earphones are connected, sound output from speaker will be muted. • When external microphone is connected, no record can be made from built-in microphone. Player on/off Press to turn on the player. Press to turn off the player. Keys lock To avoid accidental key activation, slide the key lock selector toward the lock icon ( ) to lock the keys. Reverse the step to unlock them. General controls Setting day and time Basic operations 1 2 Display 8 1 9 6 11 2 10 7 12 3 11 4 3 8 5 5 13 6 12 13 9 4 7 14 10 15 16 1. Built-in microphone 2. Recording indicator 3. MENU - press once to access folders, press and hold to access the player menu for various settings 4. ERASE - erases files 5. VOLUME - adjusts volume, selects / browses in the player menu 6. REC - starts and pauses recording 7. OFF - stops playback or recording, turns off player 8. ON - turns on player, starts or pauses playback 9. FWD/ REW - skips / searches backward or forward, selects / browses in the player menu 10. Key lock selector 11. MIC - External microphone jack 12. EAR - External earphones jack 13. USB jack 1. Folder (A/B/C/D) 2. File selected 3. Total number of files in a folder 4. Playback in progress 5. Recording in progress 6. Playback speed 7. Total remain time for recording 8. Battery level indicator 9. Key lock function activated 10. Time, date, record time 11. Bookmark 12. Recording conditions 13. Automatic voice recording activated 14. Area for display messages (refer to the next section) 15. Recording qualities 16. Playback mode: play one or play all Display messages The messages show at the bottom of the display during operation. Refer to the below for their meanings: ALL APPEND CUT-E CUT-S FULL MM/DD 12 HOUR TIME INSERT INTRO OFF ON SEN MI TONE NO TONE VOL 15 YEAR LOCKED FORMAT SPEED WAIT... PCLINK LOBATT DEL 01 DEL AL Select all (Introductory Play back & Erasing All Files) Appendix (Adding Appendix) Cut End (Cutting) Cut Start (Cutting) Memory full Month / day entry mode. 12 hour time display mode. Time entry mode Insertion (Inserting New Segments) Introduction (Introductory Playback) Off (Automatic Voice Recording) On (Automatic Voice Recording) Sensitivity Level (AVR) Beeping sound on (Setting Beep Sound) No beeping sound (Setting Beep Sound) Volume (Setting Volume) Year (Setting Year) Key locked Format the memory Speed of playback Memory rearrangement/System is busy Player is connected to the computer Battery level is low Delete the selected file (e.g. file 01) Delete all files in a folder With day and time set, you can always read on the display the recording date and time of your recorded messages. Normal recording is still possible without setting. However, no correct recording date and time can be referred to your recorded messages. Follow the steps below for setting day and time: 1. Press to turn on the player. 2. Press and hold MENU for about 2 seconds and DICT then release the button. The first menu item, DICT or CONF flashes on display. 3. Press MENU again repeatedly until YEAR shows. • If day and time have not been set previously, the player goes to step 3 automatically after turn on. 4. When YEAR shows, press / or VOL +/- to adjust the value (default year: 2008) and then press MENU to confirm. 5. After year is set, you will then be guided to set month, day, 12/24 hour display, hour and minute. Follow the operations in step 4 for settings. / or VOL +/- Press MENU MM DD / or VOL +/- Press MENU AM / or VOL +/- Press MENU AM / or VOL +/- Press MENU Exit time setting mode Select folders Press MENU A AM repeatedly to select DICT a specific folder (A/B/ REMAIN SP C/D) for browsing. Default is folder A. Select files To select a specific file for playback: 1. Select the folder you need. 2. Press or to select the file you want. If the file you want is in the current folder, you can press or to select it directly in both stop and play modes. Normal playback 1. Select a folder and a file. 2. Press to start playback. 3. Press to pause playback, press again to resume. 4. You can press VOLUME +/- to adjust listening volume. 5. Press and hold or to make quick search within a file. • Quick search skips by second within the first minute of a recording. After that, the search skips by minute. To resume searching by second, release the button once and then press and hold or again. 6. Press or once to skip one file forward or backward. 7. Press to stop playback. "ALL" is displayed if you are at the first file and press or at the last file and press . See IntroScan for more detail. Using MENU key Bookmark Recording The MENU key has two functions: Accessing folders Press MENU repeatedly to select folders (A/B/C/D). Press MENU repeatedly Accessing player menu 1. Press and hold MENU for about 2 seconds and then release the button. The first menu item, DICT or CONF flashes on display. DICT Press and hold MENU for about 2 seconds to access the player menu 2. Then press MENU again repeatedly to select the following menu items: Record conditions (DICT/CONF) Record quality (HQ/SP) AVR (on/off) Speed (FAST/SLOW) Playback mode (one/all) Tone (on/off) Year Day (month/day) 12/24 hour time Time (hour/minute) Exit player menu 3. Press / or VOL +/- to make selections or adjust values. 4. Press to confirm your selection and exit setting. Erasing files Creating a bookmark This feature allows you to create an interception point in the recorded message for quick reference. 1. During playback, press REC once to set a bookmark, the bookmark icon flashes on the display. • The month and date information is displayed, followed immediately by the counters for the bookmarks. current bookmark total number of bookmarks 2. You can create multiple bookmarks until "FULL" is displayed. Deleting bookmarks 1. Press MENU repeatedly to select a folder (A/B/C/D). 2. Press or to select a file. 3. Press ERASE once and DEL XX (XX is the file number) will flash on the screen. 4. Press and hold for 3 seconds to confirm deleting ALL bookmarks in the file. You can create up to 29 bookmarks in a file. When the maximum limit is reached, "FULL" will be shown. Skipping to a bookmark You can skip to a bookmark anytime during playback. 1. During playback, press to go to the bookmark (if available). 2. Press again to go to the next bookmark. Advanced operations Setting recording mode You can select between two recording modes - manual recording and AVR (automatic voice recording). Manual Recording 1. While playback is stopped, select a destination folder (A/B/C/D) by pressing MENU repeatedly. 2. Press REC to start recording. (recording time will be displayed once you press REC) 3. To pause recording, press REC once, press again to resume recording. 4. To stop recording, press . AVR (Automatic Voice Recording) This feature allows the player to sense sound and to record only when you are speaking into the microphone. When dictation stops for about three seconds, recording will stop and then start again automatically when you resume dictation. 1. Press MENU repeatedly to select a destination folder (A/B/C/D). 2. Press and hold MENU for about 2 seconds and then release the button. The first menu item, DICT or CONF flashes on display. 3. Then press MENU again repeatedly until AVR flashes on display. 4. Press / or VOL +/- to select between AVR on and AVR off. AVR 5. Press to confirm your selection and exit setting. 6. Press REC to enter AVR mode. 7. During AVR A recording, adjust AM the sensitivity of DICT the microphone SP AVR by pressing VOLUME, SEN with sensitivity level will show on display (e.g. increase sensitivity level when recording source is far from the player or the recording environment is quiet). 8. Start dictation. Recording starts automatically. 9. Press to end AVR recording. • Repeat step 2-3 and select AVR OFF for de-selection. • During recording, the recording indicator lights. When in AVR standby mode or when recording is paused, the recording indicator flashes. • You can record up to 99 files in one folder, not exceeding 396 files in total. When the maximum limit is reached, "FULL" will be shown. • The first syllable or two may be lost when you start recording because this 'sound' is used to turn on the AVR feature. It is a good practice to make some 'sounds' or say a short word to activate the AVR before you begin actual dictation. • To view the remaining time and other recording information, you may press and hold during recording. Editing Setting recording quality You can select between two recording qualities. Default is HQ. Definition • SP (Standard Play) - allows about 104 hours recording. • HQ (High Quality) - allows about 18 hours recording. 1. Press and hold MENU for about 2 seconds and then release the button. The first menu item, DICT or CONF flashes on display. 2. Then press MENU again repeatedly until SP or HQ flashes SP on display. 3. Select between SP and HQ by pressing / or VOL +/-. 4. Press to confirm your selection and exit setting. Setting recording condition You can select between two recording conditions. Default is DICT. Definition • CONF (Conference) - in a more open area and recording source is far from the player. • DICT (Dictation) - in a more enclosed area and recording source is close to the player. 1. Press and hold MENU for about 2 seconds and DICT then release the button. The first menu item, DICT or CONF flashes on display. 2. Select recording condition by pressing / or VOL +/-. 3. Press to confirm your selection and exit setting. • For conferences, to obtain optimum recording quality, place the recorder with the microphone freely exposed to the sound source as close as convenient. A built-in automatic recording level control will set the optimum record level during manual recording. Avoid recording near unwanted noise sources, such as air conditioners or fans. • If power supplied from the battery fails suddenly (e.g. batteries are removed accidentally) during recording, the recoding in progress will be interrupted. The recorded file may also be corrupted and cannot be played back. Erasing selected file To delete a file: 1. Press MENU repeatedly to select a folder (A/B/C/D). 2. Press or to select a file. 3. Press ERASE once and DEL XX (XX is the file number) will flash on the display. 4. Press and hold ERASE for three seconds to confirm deleting. To avoid accidental deletion of all files, make sure you press ERASE only when you are reading the time duration of the undesired file instead of the remaining recordable time of the player. Erasing all files in a folder To delete all files in a specific folder: 1. Press MENU repeatedly to select a folder (A/B/C/D). 2. While playback is stopped, press repeatedly until ALL appears on the display. 3. Press ERASE and DEL AL will flash on the display. 4. Press and hold ERASE for about three seconds, all files in the selected folder will be erased completely. • Press to cancel erasing all files. File numbers that come after erased one will be moved forward by one automatically. IntroScan This feature allows playback of the first three seconds of each file in a folder. 1. Press MENU repeatedly to select a folder (A/B/C/D). 2. Press or A MM DD AM ONE SP DICT until ALL shows on display A MM DD 3. Press to start introductory ONE playback, INTRO SP shows on display. 4. Press to exit IntroScan sooner. Play one/all You can choose to play a specific file or all files in a folder. 1. Press and hold MENU for about 2 seconds and then release the button. The first menu item, DICT or CONF flashes on display. 2. Then press MENU again repeatedly until ONE or ALL flashes on display. 3. Press / or VOL +/- to select between ONE and ALL. 4. Press to confirm your selection and exit setting. • If ONE is selected, the player will stop after the selected file is played. If ALL is selected, the player will stop after all files in a folder are played. Tones You can activate this feature so that beep sound can be heard whenever you press on any key except during playback and recording. 1. Press and hold MENU for about 2 seconds and then release the button. The first menu item, DICT or CONF flashes on display. 2. Then press MENU again repeatedly until TONE or NOTONE shows on display. 3. Press / or VOL +/- to set beep sound ON/OFF. 4. Press to confirm your selection and exit setting. Speed You can adjust the playback speed. 1. Press to start playback of a selected file. 2. During playback, press MENU once, SPEED FAST shows on display. 3. Press / or VOL +/- to select between FAST, SLOW and no speed indication (normal speed). 4. Press to confirm and start playback at the selected speed. Format (Caution! All data inside the memory will be erased) You can format the internal memory when needed. (e.g. compatability problem, etc.) The procedures are as follow: 1. Turn on the player. 2. Press ERASE, A DEL XX (XX is the MM DD file number) or DEL AL will flash ONE SP DICT on the display. 3. Press and hold REC for three A MM DD seconds, FORMAT will flash on the display. ONE SP DICT 4. Press and hold ERASE, WAIT will show on the display, formatting is in process. • After the formatting is completed, the remain time of the selected memory will show on the display. You may also format the player when connected to a PC (by rightclicking on the player's drive name or letter and select "Format" from the menu). Make sure you select FAT or FAT16 as the file system. CAUTION • The edit function does not operate when battery power is too low. • Make sure play all files is not selected. Inserting new segments, adding appendix and cutting cannot be performed when play all files is selected. • After editing a message, WAIT will be displayed. Do not power off the player until WAIT disappears. Otherwise, the memory which is rearranging could not be read or released until the player is formatted. Insert You can insert new segments into a file without erasing previously recorded content. 1. Press to start playback of a selected file. 2. Press or to scan to the point that you want to insert new segment. 3. Press MENU A AM twice, INSERT will be shown on ONE display. Press REC SP within three seconds to start recording new segment. 4. Press to stop recording. Append You can add appendix (e.g. reminder, supplementary informa- tion) to the end of the file. 1. Press to start playback of a selected file. 2. Press MENU A three times, AM APPEND shows ONE on display. Press SP REC within three seconds to start recording appendix. 3. Press to stop recording. • After the memory rearrangement completed, the player will go to playback stop mode. Cut You can erase unwanted parts from your recording. 1. Press to start playback of the file with the unwanted part. 2. Press ERASE to A mark the start AM of the unwanted part, CUT-S shows SP on display. 3. Press ERASE to A mark the end of AM the unwanted part, CUT-E shows SP on display. 4. Press ERASE again to confirm cutting (or press to cancel) • WAIT will show on display. • When the memory rearrangement is completed, the player will continue the playback. • Inserting new segments, adding appendix and cutting will only update the recorded time length, without changing recording time and date. • All bookmarks will be deleted after inserting new segments, adding appendix or cutting is performed. Connecting to computer Using Digital Voice Manager Computer system requirements • PC with Windows VistaTM or Windows® XP (Service Pack 1 or higher) or Windows® 2000 (Service Pack 3 or higher) • 20MB free hard disk space for software • USB port 1.1 or 2.0 • Installed sound card Connecting to computer Connect the player before launching the Digital Voice Manager. 1. Connect the USB cable provided to the player's USB jack and connect the other end to your computer's USB port. 2. "PCLINK" shows on the player's display. The player appears as a removable drive in your computer. Installing Digital Voice Manager 1. Connect the player with the computer as instructed in the previous section. 2. Double click or open the "MyComputer" desktop icon, then double click the player drive icon. 3. Double click "SETUP" folder, then double click "Setup" or Setup.exe to run the installer. 4. Follow the on-screen instructions to install the software. 5. After installation is completed, reboot your computer. • The Digital Voice Manager software can also be downloaded from www.rcaaudiovideo.com • When the player is in Menu mode, during playback or recording, a connection between the player and the computer will not be established. Quit the above modes before connecting to the computer. • Data transfer is possible even if no batteries are installed in the player. • Do not disconnect the USB connection during files transfer. The RCA Digital Voice Manager can perform playback, organize your bookmarks of the recorded files and create self-executable voice file from the recorded files. Launching the software 1. To launch the software, click "Start", select "All Programs", select "Digital Voice Recorder", then select "RP5120" and then select "Digital Voice Manager". 2. All the drives in the computer except the removable Digital Voice Recorder are shown in the top while the removable Digital Voice Recorder is shown in the bottom. All drives in the computer Removable Digital Voice Recorder Playback and editing operations 1. To organize your files, click the corresponding buttons to cut, delete, copy and paste a file (or by drag and drop). cut paste copy delete 2. To play the recorded files, highlight the file and click the PLAY/PAUSE button on the left of the toolbar. play/pause skip forward stop clear bookmark stop playback of a recorded file. • To adjust the playback speed, click "Normal Speed" and select desired speed from the pull down menu. 4. To skip to a bookmark, select "Play" from the menu at the top, then select "Goto Bookmark" and select your desired bookmark. • To edit bookmarks, click the corresponding buttons to add or clear the bookmarks. skip backward skip to a add bookmark specific time 3. Adjust the volume on the right of the toolbar. adjust volume • Click the corresponding buttons in the toolbar to fast backward/forward, skip to a specific time in the file and Creating and playing selfexecutable file You can play the created file independently without the Digital Voice Management software. 1. Highlight a recorded file, click . 2. Select the destination folder from the pop up window and click "Save". 3. Go to the destination folder and double-click the created file. 4. Click "Play" to start playback. Adjust the volume on the right. Creating wave file Self-executable file may be blocked by some e-mail filters. You may select to create wave file if you want to send your recorded message by e-mail. 1. Highlight a recorded file, click . 2. Select the destination folder from the pop up window and click "Save". 3. The created file could be found in the destination folder. Transfer files with Digital Voice Manager (Voice files only) Your player is associated with a drive letter. You can drag the voice files you want to transfer to your player to the A/B/C/D folder in the drive. Your files can be found in these folders in the player once it is disconnected from the computer. You can also drag the voice files you want to transfer from the A/B/C/D folder in the drive to your computer. All drives in the computer Removable Digital Voice Recorder Using your player as a file storage device The player can function as a detachable data storage device. You can take along your favorite pictures and documents wherever you go. Simply cut-and-paste or drag-and-drop files to or from it via USB connection, the player will appear as a removable drive in Windows Do not rename, delete and transfer (drag-anddrop) voice files to your player directly in Windows Explorer. Use the Digital Voice Manager to rename, delete and transfer voice files. Disconnecting from computer After you have copied files to or from the player, you can disconnect the player from the computer. 1. Click the icon from the System Tray and select "Unplug or Eject hardware". Select the drive corresponding to your player. 3. Now you can disconnect the player from the computer. If you want to go back to USB mode for file transfer at this stage, you need to unplug and connect the player to the PC again. Thomson RP5022A / RP5120-A USB Device 2. The "Stop a Hardware player" screen will appear. Select the player to be stopped again for confirmation and click OK. Thomson RP5022A / RP5120-A USB Device Troubleshooting tips Player doesn't turn on • Check that batteries are properly inserted and not exhausted. • Make sure battery compartment door is properly closed. • Make sure LOCK function is not activated. Display keeps flashing when player is off • You may not have set the time. Refer to section "Time Setting". Cannot record • Make sure LOCK function is not activated. • Make sure memory is not full. • You have recorded 99 files in one folder. Try record in a new folder. • You may have formatted the player with incorrect file system (e.g. FAT32). Refer to section "Format" and format the player again. Incorrect recording date and time during playback • You may have not set the date and time before recording. Refer to section 'Time Setting'. No sound from speaker during playback • Make sure volume is not set to 0. • Headphones should not be connected. Cannot edit • Make sure LOCK function is not activated. Cannot activate the player after pressing on keys • Remove the batteries to reset the player. Recordable time becomes shorter • You may have set the recording quality to 'High Quality', refer to section 'Setting Recording Quality'. • Delete the Digital Voice Manager setup software from the player to free up more memory space. Cannot perform playback • Make sure you have selected folder with recorded messages. • Make sure LOCK function is not activated. Cannot erase recorded file(s) • Make sure you follow each step under section "Erasing Selected File" carefully. Cannot stop recording when AVR ON • If AVR ON sensitivity is set to HIGH, recording may not be stopped in noisy environment. Try setting the sensitivity to LOW. Cannot keep the saved setting • If the batteries are removed, saved settings may be removed. Cannot open recorded files in the computer. • You must use the provided DVM software to open the files. • To download the software, go to www.rcaaudiovideo.com Warranty information 12 Month Limited Warranty Applies to RCA Audio/Video Products • AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair labor. • To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the Company at the address shown below. • This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, loss/interruptions of broadcast or internet service, to costs incurred for installation, removal or reinstallation of product, to corruptions caused by computer viruses, spyware or other malware, to loss of media, files, data or content, or to damage to tapes, discs, removable memory devices or cards, speakers, accessories, computers, computer peripherals, other media players, home networks or vehicle electrical systems. • This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT. • This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY. No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product. • Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state. How to make a warranty claim: • If your product is capable of storing content (such as an mp3 player, digital voice recorder, etc), it is recommended to make periodic backup copies of content stored on the product. If applicable, before shipping a product, make a back up copy of content or data stored on the device. Also, it is advisable to remove any personal content which you would not want exposed to others. IT IS LIKELY THAT CONTENTS AND DATA ON THE DEVICE WILL BE LOST DURING SERVICE AND REFORMATTING. AUDIOVOX ACCEPTS NO LIABILITY FOR LOST CONTENT OR DATA, OR FOR THE SECURITY OF ANY PERSONAL CONTENT OR DATA ON THE RETURNED DEVICE. Product will be returned with factory default settings, and without any pre-loaded content which may have been installed in the originally purchased products. Consumer will be responsible for reloading data and content. Consumer will be responsible to restore any personal preference settings. • Properly pack your unit. Include any remotes, memory cards, cables, etc. which were originally provided with the product. However DO NOT return any removable batteries, even if batteries were included with the original purchase. We recommend using the original carton and packing materials. • Include evidence of purchase date such as the bill of sale. Also print your name and address and a description of the defect. Send via standard UPS or its equivalent to: Audiovox Electronics Corp. Attn: Service Department. 150 Marcus Blvd. Hauppauge N.Y. 11788 1-800-645-4994 • Insure your shipment for loss or damage. Audiovox accepts no liability in case of damage or loss en route to Audiovox. • Pay any charges billed to you by the Exchange Center for service not covered by the warranty. • A new or refurbished unit will be shipped to you freight prepaid. What we will do: Provide you with a new, or at our option, a refurbished unit. The exchange unit is under warranty for the remainder of the original product's warranty period. For Canada Customers, please ship to: Audiovox Return Centre c/o Genco 6685 Kennedy Road, Unit#3, Door 16, Mississuaga, Ontario L5T 3A5 The descriptions and characteristics given in this document are given as a general indication and not as a guarantee. In order to provide the highest quality product possible, we reserve the right to make any improvement or modification without prior notice. The English version serves as the final reference on all products and operational details should any discrepancies arise in other languages. Audiovox Electronics Corp., 150 Marcus Blvd, Hauppauge, NY 11788 1-800-283-6503 ©2008 Audiovox Electronics Corp. Trademark(s) © Registered Marca(s) © Registrada(s) Marque(s) © Deposée(s) www.rcaaudiovideo.com Printed in China/Impreso en China