Avanti CTW84X0W-IS Instruction Manual - Page 8

Installation Instructions

Get Avanti CTW84X0W-IS PDF manuals and user guides View all Avanti CTW84X0W-IS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

INSTALLATION INSTRUCTIONS BEFORE USING YOUR PORTABLE WASHER · Remove the exterior and interior packing. · You will need the following tools: · Wrench · Pliers · Screwdriver · Check to be sure you have all of the following parts: · 1 Inlet Hose · 1 Faucet Adapter · 1 Drain Hose Assembly SCREWDRIVER WRENCH PLIERS · Remove shipping brace. Note - It should be saved and used (to prevent damage to washer components) whenever washer is moved or transported to a new location. · Clean the interior surface with lukewarm water using a soft cloth. · Allow 2 inches of space between the back and sides of the appliance. · Put your laundry into the washer evenly. Uneven laundry may cause noise or vibration. · DO NOT use excessively hot water (122ºF / 50°C or more). Plastic parts may be deformed or damaged. Also, clothing may be deformed or bleached. · Before washing, check all pockets. If nails or pins remain in pockets, they may damage the washer or clothes. · Never splash water on the control panel. · Plug the washer into an exclusive properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an Authorized Avanti Products service center. SELECTING A LOCATION Before you install the portable washer, select a location with the following characteristics: · A hard level surface (if the surface is uneven, see Adjusting The Adjustable Foot section on the next page). · Away from direct sunlight. Direct sunlight may affect the acrylic coating, plastic and electrical components. · Adequate ventilation. · Away from sources of heat such as coal or gas. Make sure that the washing machine does not stand on its power cord. · Ventilation openings must not be obstructed by carpeting when the portable washer is installed on a carpeted floor. · It is recommended that you place your portable washer on a hard material floor such as tile, concrete, linoleum and to avoid if at all possible placement on wooden floors or carpeted areas. MOVING YOUR WASHER To move your washer, tilt the unit back onto its rear rollers and push it forward as shown in the figure. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
8
INSTALLATION INSTRUCTIONS
BEFORE USING YOUR PORTABLE WASHER
•
Remove the exterior and interior packing.
•
You will need the following tools:
•
Wrench
•
Pliers
•
Screwdriver
•
Check to be sure you have all of the following parts:
•
1 Inlet Hose
•
1 Faucet Adapter
•
1 Drain Hose Assembly
•
Remove shipping brace. Note - It should be saved and used (to prevent damage to washer
components) whenever washer is moved or transported to a new location.
•
Clean the interior surface with lukewarm water using a soft cloth.
•
Allow 2 inches of space between the back and sides of the appliance.
•
Put your laundry into the washer evenly.
Uneven laundry may cause noise or vibration.
•
DO NOT use excessively hot water (122ºF / 50°C or more). Plastic parts may be deformed or
damaged.
Also, clothing may be deformed or bleached.
•
Before washing, check all pockets.
If nails or pins remain in pockets, they may damage the
washer or clothes.
•
Never splash water on the control panel.
•
Plug the washer into an exclusive properly installed-grounded wall outlet.
Do not under any
circumstances cut or remove the third (ground) prong from the power cord.
Any questions
concerning power and/or grounding should be directed toward a certified electrician or an
Authorized Avanti Products service center.
SELECTING A LOCATION
Before you install the portable washer, select a location with the following
characteristics:
•
A hard level surface (if the surface is uneven, see Adjusting The
Adjustable Foot section on the next page).
•
Away from direct sunlight.
Direct sunlight may affect the acrylic coating,
plastic and electrical components.
•
Adequate ventilation.
•
Away from sources of heat such as coal or gas.
Make sure that the
washing machine does not stand on its power cord.
•
Ventilation openings must not be obstructed by carpeting when the
portable washer is installed on a carpeted floor.
•
It is recommended that you place your portable washer on a hard material
floor such as tile, concrete, linoleum and to avoid if at all possible
placement on wooden floors or carpeted areas.
MOVING YOUR WASHER
To move your washer, tilt the unit back onto its rear
rollers and push it forward as shown in the figure.
WRENCH
PLIERS
SCREWDRIVER