Avanti OBC33SSD Instruction Manual - Page 12

Operating Your Refrigerator, Model Obc33ssd - beverage center refrigerator

Get Avanti OBC33SSD PDF manuals and user guides View all Avanti OBC33SSD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

OPERATING YOUR REFRIGERATOR (MODEL OBC33SSD) IMPORTANT SAFEGUARDS As a natural result of condensation, in summer months or areas of high humidity, the glass door may build up moisture on the outside. Just wipe it away. It is recommended you install the Refrigerator in a place where the ambient temperature is between 50ºF - 100ºF (10º - 38ºC ). If the ambient temperature is above or below recommended temperatures, the performance of the unit may be affected. For example, placing your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate. The range of 36º - 64º F (2º - 18º C) may not be reached.  CONTROL PANEL (MODEL OBC33SSD - ONLY) The unit turns on automatically once plugged in. Your beverage center is equipped with an electronic display that once any button is pressed the display window will light on and will automatically light off two (2) minutes after the last button was pressed. Alarm Indicator Compressor Run Indicator Temperature Display SET Button Temperature UP / DOWN Light Switch CONTROL PANEL FEATURES / DESCRIPTIONS Alarm mode: In the event there is a fault in the unit, an Alarm indicator will appear in the area shown above on the control panel. If at any time the following messages are shown in the display window, consult an Avanti Products Authorized Service Center.  PROBE ERROR  LOW TEMP  HIGH TEMP When the unit's compressor is running, the control panel will display a moving "FAN" icon. Once the compressor stops running the icon will also stop moving. The set temperature and current average temperature of the unit will be displayed in this area as shown above. Use this button to activate the temperature setting mode and again to confirm the selected temperature setting. Use these buttons to select the appropriate temperature. Temperature setting will either advance or decrease each time you press the respective button. The interior light can be operated manually by pressing the ON/OFF button on the control panel. The light will automatically turn itself OFF after 5 minutes. NOTE: Avoid extended use of the light as the heat generated by the light bulb can raise the interior temperature of the unit and affect the temperature of the items stored. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
12
OPERATING YOUR REFRIGERATOR
(MODEL OBC33SSD)
It is recommended you install the Refrigerator in a place where the ambient temperature is between
50ºF - 100ºF (10º - 38ºC ).
If the ambient temperature is above or below recommended
temperatures, the performance of the unit may be affected.
For example, placing your unit in
extreme cold or hot conditions may cause interior temperatures to fluctuate.
The range of 36º - 64º F
(2º - 18º C) may not be reached.
CONTROL PANEL (MODEL OBC33SSD – ONLY)
The unit turns on automatically once plugged in.
Your beverage center is equipped with an electronic display that once any button is pressed the
display window will light on and will automatically light off two (2) minutes after the last button was
pressed.
CONTROL PANEL FEATURES / DESCRIPTIONS
Alarm Indicator
Alarm mode:
In the event there is a fault in the unit, an Alarm indicator
will appear in the area shown above on the control panel.
If at any time the following messages are shown in the display window,
consult an Avanti Products Authorized Service Center.
PROBE ERROR
LOW TEMP
HIGH TEMP
Compressor Run
Indicator
When the unit’s compressor is running, the control panel will display a
moving “FAN” icon.
Once the compressor stops running the icon will
also stop moving.
Temperature Display
The set temperature and current average temperature of the unit will be
displayed in this area as shown above.
SET Button
Use this button to activate the temperature setting mode and again to
confirm the selected temperature setting.
Temperature
UP / DOWN
Use these buttons to select the appropriate temperature.
Temperature
setting will either advance or decrease each time you press the
respective button.
Light Switch
The interior light can be operated manually by pressing the ON/OFF
button on the control panel.
The light will automatically turn itself OFF
after 5 minutes.
NOTE:
Avoid extended use of the light as the heat generated by the light
bulb can raise the interior temperature of the unit and affect the
temperature of the items stored.
IMPORTANT SAFEGUARDS
As a natural result of condensation, in summer months or areas of high humidity, the glass door
may build up moisture on the outside.
Just wipe it away.