Avanti WC3015S3S Instruction Manual - Page 9

Installation Instructions

Get Avanti WC3015S3S PDF manuals and user guides View all Avanti WC3015S3S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

INSTALLATION INSTRUCTIONS  BEFORE USING YOUR WINE CHILLER  Remove the exterior and interior packing.  Check to be sure you have all of the following parts: 1 Instruction Manual Large Shelves Model: WC3015S3S - Total 5 1 Small Shelf 1 Stainless Steel Handle 1 Set Hinges for Door Swing Reversal 2 Keys  Before connecting this appliance to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.  Clean the interior surface with lukewarm water using a soft cloth.  INSTALLATION OF YOUR WINE CHILLER  This appliance is designed to be for free standing installation or built-in (fully recessed).  Place your Wine Chiller on a floor that is strong enough to support it when it is fully loaded. To level your Wine Chiller, adjust the front leveling legs at the bottom of the Wine Chiller.  Locate the Wine Chiller away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the unit not to perform properly.  Avoid locating the unit in moist areas.  Plug the Wine Chiller into an exclusive, properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorized Avanti Products service center.  BUILT - IN CABINET INSTRUCTIONS This unit is designed for both built-in or free standing installation. If you plan to use this unit in a builtin application please follow the requirements shown below. ← Figure shown Cabinet Opening Dimensions IN (min) MM (min) Width 15 ¼" 388 mm Depth 24" 610 mm Height 35" 889 mm → Figure shown Unit Dimensions IN (min) MM (min) Width 15" 380 mm Depth 24 ¾" 630 mm (with handle) Depth (without handle) 23 ¼" 590 mm Height 34" 864 mm 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
9
INSTALLATION INSTRUCTIONS
BEFORE USING YOUR WINE CHILLER
Remove the exterior and interior packing.
Check to be sure you have all of the following parts:
1
Instruction Manual
Large Shelves
Model:
WC3015S3S – Total 5
1
Small Shelf
1
Stainless Steel Handle
1 Set
Hinges for Door Swing Reversal
2
Keys
Before connecting this appliance to the power source, let it stand upright for approximately 2
hours. This will reduce the possibility of a malfunction in the cooling system from handling
during transportation.
Clean the interior surface with lukewarm water using a soft cloth.
INSTALLATION OF YOUR WINE CHILLER
This
appliance is designed to be for free standing installation or built-in (fully recessed).
Place your Wine Chiller on a floor that is strong enough to support it when it is fully loaded. To
level your Wine Chiller, adjust the front leveling legs at the bottom of the Wine Chiller.
Locate the Wine Chiller away from direct sunlight and sources of heat (stove, heater, radiator,
etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical
consumption. Extreme cold ambient temperatures may also cause the unit not to perform
properly.
Avoid locating the unit in moist areas.
Plug the Wine Chiller into an exclusive, properly installed-grounded wall outlet. Do not under
any circumstances cut or remove the third (ground) prong from the power cord. Any questions
concerning power and/or grounding should be directed toward a certified electrician or an
authorized Avanti Products service center.
BUILT – IN CABINET INSTRUCTIONS
This unit is designed for both built-in or free standing installation.
If you plan to use this unit in a built-
in application please follow the requirements shown below.
←
Figure shown
Cabinet Opening Dimensions
IN (min)
MM (min)
Width
15 ¼”
388 mm
Depth
24”
610 mm
Height
35”
889 mm
Figure shown
→
Unit Dimensions
IN (min)
MM (min)
Width
15
”
380 mm
Depth
(with handle)
24 ¾”
630 mm
Depth
(without handle)
23
¼”
590
mm
Height
34”
864 mm