Axis Communications M7016 M7016 Video Encoder - User Manual - Page 5

toc, yHardware Overview, Connectors and Buttons, BNC Connector, Network Connector - encoder

Get Axis Communications M7016 PDF manuals and user guides View all Axis Communications M7016 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

AXIS M7016 Video Encoder Hardware Overview Hardware Overview 1 1 Video input connector BNC x16 2 Status LED 1-4 3 Power LED 4 Network activity LED RJ45 12 34 5 23 4 6 1 Power connector 2 Network connector RJ45 3 Card slot microSD x4 4 RS-485/422 connector x4 5 Control button x4 6 Protective earth Connectors and Buttons For technical specifications, see page 50. BNC Connector Each video input is terminated using a coax/BNC connector. Connect a 75 Ohm coaxial video cable; the recommended maximum length is 250 m (800 ft). Note 75 Ohm video termination can be enabled/disabled for the video input through the product's web page at Video > Camera Settings > Video termination. This termination is enabled on factory default. In cases where the product is to be connected in parallel with other equipment, for optimum video quality, it is recommended that termination be enabled for only the last device in the video signal chain. Network Connector RJ45 Ethernet connector. NOTICE The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network switch shall be shielded (STP) and intended for their specific use. Make sure that the network switch is properly grounded. For information about regulatory requirements, see Regulatory Information, on page 2 . Power Connector 2-pin terminal block for power input. Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
AXIS M7016 Video Encoder
Hardware Overview
Hardware Overview
1
Video input connector BNC x16
2
Status LED 1–4
3
Power LED
4
Network activity LED RJ45
1
Power connector
2
Network connector RJ45
3
Card slot microSD x4
4
RS-485/422 connector x4
5
Control button x4
6
Protective earth
Connectors and Buttons
For technical specifications, see
page 50
.
BNC Connector
Each video input is terminated using a coax/BNC connector. Connect a 75 Ohm coaxial video cable; the recommended maximum
length is 250 m (800 ft).
Note
75 Ohm video termination can be enabled/disabled for the video input through the product's web page at
Video > Camera
Settings > Video termination
. This termination is enabled on factory default. In cases where the product is to be connected
in parallel with other equipment, for optimum video quality, it is recommended that termination be enabled for only the last
device in the video signal chain.
Network Connector
RJ45 Ethernet connector.
NOTICE
NOTICE
NOTICE
The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network switch
shall be shielded (STP) and intended for their specific use. Make sure that the network switch is properly grounded. For
information about regulatory requirements, see
Regulatory Information, on page 2
.
Power Connector
2-pin terminal block for power input. Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated
output power limited to
≤
100 W or a rated output current limited to
≤
5 A.
5