Axis Communications P1214 P1214 Network Camera - User Manual - Page 9

The Live View

Get Axis Communications P1214 PDF manuals and user guides View all Axis Communications P1214 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

AXIS P1214 Network Camera Access the Product Select the power line frequency (50 Hz or 60 Hz) used at the location of the Axis product. Selecting the wrong frequency may cause image flicker if the product is used in fluorescent light environments. When using 50 Hz, the maximum frame rate is limited to 25 fps. Note Power line frequency varies depending on geographic region. The Americas usually use 60 Hz, whereas most other parts of the world use 50 Hz. Local variations could apply. Always check with the local authorities. The Live View Page The controls and layout of the Live View page may have been customized to meet specific installation requirements and user preferences. Consequently, some of the examples and functions featured here may differ from those displayed in your own Live View page. The following provides an overview of each available control. Controls on the Live View Page Click View size to scale the image down to 800 pixels wide or to full scale. Only available in MJPEG. Select a stream profile for the Live View page from the Stream Profile drop-down list. For information about how to configure stream profiles, see page 17. Click Pulse to activate the product's output port for a defined period of time. For information about how to enable and configure output buttons, see page 21. Click the Active/Inactive buttons to manually activate and inactive the product's output port. For information about how to enable and configure output buttons, see page 21. The Manual Trigger button is used to trigger an action rule from the Live View page. For information about how to configure and enable the button, see Manual Trigger on page 9 . Click Snapshot to save a snapshot of the video image. This button is primarily intended for use when the AXIS Media Control viewer toolbar is not available. Enable this button from Live View Config > Action Buttons. Manual Trigger The Manual Trigger is used to trigger an action rule from the Live View page. The manual trigger can for example be used to validate actions during product installation and configuration. To configure the manual trigger: 1. Go to Setup > Events. 2. Click Add to add a new action rule. 3. From the Trigger drop-down list, select Input Signal. 4. From the second drop-down list, select Manual Trigger. 5. Select the desired action and configure the other settings as required. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
AXIS P1214 Network Camera
Access the Product
Selectthepowerlinefrequency(50Hzor60Hz)usedatthelocationoftheAxisproduct.Selectingthewrongfrequencymaycause
image flicker if the product is used in fluorescent light environments.
When using 50 Hz, the maximum frame rate is limited to 25 fps.
Note
Power line frequency varies depending on geographic region. The Americas usually use 60 Hz, whereas most other parts of
the world use 50 Hz. Local variations could apply. Always check with the local authorities.
The Live View Page
The controls and layout of the Live View page may have been customized to meet specific installation requirements and user
preferences.Consequently,someoftheexamplesandfunctionsfeaturedheremaydifferfromthosedisplayedinyourownLiveView
page. The following provides an overview of each available control.
Controls on the Live View Page
Click
Viewsize
to scale the image down to 800 pixels wide or to full scale. Only available in MJPEG.
SelectastreamprofilefortheLiveViewpagefromthe
StreamProfile
drop-down list. For information about how
to configure stream profiles, see
page17
.
Click
Pulse
to activate the product’s output port for a defined period of time. For information about how to
enable and configure output buttons, see
page21
.
Click the
Active/Inactive
buttons to manually activate and inactive the product’s output port. For information
about how to enable and configure output buttons, see
page21
.
The
ManualTrigger
buttonisusedtotriggeranactionrulefromtheLiveViewpage.Forinformationabouthowto
configure and enable the button, see
Manual Trigger on page 9
.
Click
Snapshot
to save a snapshot of the video image. This button is primarily intended for use when the
AXISMediaControlviewertoolbarisnotavailable.Enablethisbuttonfrom
LiveViewConfig>ActionButtons
.
Manual Trigger
The
ManualTrigger
is used to trigger an action rule from the Live View page. The manual trigger can for example be used to
validate actions during product installation and configuration.
To configure the manual trigger:
1. Go to
Setup>Events
.
2. Click
Add
to add a new action rule.
3. From the
Trigger
drop-down list, select
InputSignal
.
4. From the second drop-down list, select
ManualTrigger
.
5. Select the desired action and configure the other settings as required.
9