Behringer AB200 Manual - Page 1

Behringer AB200 Manual

Get Behringer AB200 PDF manuals and user guides View all Behringer AB200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

DUAL A/B SWITCH AB200 Thank you for showing your confidence in us by purchasing the BEHRINGER AB200. This high-quality 2-channel A/B switch is designed for musicians who use several amps and/or instruments. The AB200 allows you to switch between gear noiselessly and instantaneously without coloring the sound of + The AB200 has no on/off switch. As soon as you insert a jack into the A1 or B1 connector, the AB200 begins running. When not using the AB200, remove the jacks from the connectors. This extends the life of the battery. your instrument. The LED always displays which element of your system is currently being used. The SERIAL NUMBER is located at the bottom of the unit. 1. CONTROLS AND CONNECTIONS 2. APPLICATIONS Fig. 1.1: Rear view Since the controls and connections of the two channels are identical, this chapter only describes channel 1. IN/OUT 1: this 1/4" TS jack serves as channel 1 input when a source is plugged in (guitar, bass etc.) and as channel 1 output when an amp or an effect is plugged in. A1 & B1: these 1/4" TS jacks serve as channel 1 outputs when amps or effects are plugged in; they serve as channel 1 inputs when instruments are plugged in. Only one of these connectors can be active at any one time. LATCH/NON LATCH: this selector determines the channel switch function: when set to LATCH, the switch is latching. When set to NON LATCH, the signal will only be routed to or from B1 as long as you hold the pedal depressed. Fig. 2.1: One instrument / two amps Plug your instrument into IN/OUT 1 and the input of each amp into one of the A1 and B1 connectors. Pressing the switch 1 will toggle between the two amps. 4 Fig. 1.2: Top view SWITCH 1: this switch allows you to assign the IN/OUT 1 signal to A1 or B1 when IN/OUT 1 is used as an input. Otherwise, the switch assigns the A1 or B1 signal to IN/OUT 1 when A1 and B1 are used as inputs. The A1 and B1 LEDs display which connector is currently active. Depending on the selector position, shortly press the switch (LATCH) or hold it down during the whole commutation time (NON LATCH) to toggle between A1 and B1. To install or replace the 9 V battery, please carefully unscrew the bottom plate and open the enclosure of the AB200. After installing close the unit again by using all screws you removed before. Fig. 2.2: Two instruments / one amp Plug each of your instruments into one of the A1 and B1 connectors and the amp input into IN/OUT 1. Pressing the switch 1 will toggle between the two instruments.

  • 1
  • 2
DUAL A/B SWITCH AB200
Thank you for showing your confidence in us by purchasing
the BEHRINGER AB200. This high-quality 2-channel A/B switch
is designed for musicians who use several amps and/or
instruments. The AB200 allows you to switch between gear
noiselessly and instantaneously without coloring the sound of
your instrument. The LED always displays which element of
your system is currently being used.
1. CONTROLS AND CONNECTIONS
Fig. 1.1: Rear view
Since the controls and connections of the two channels are
identical, this chapter only describes channel 1.
IN/OUT 1:
this 1/4" TS jack serves as channel 1 input when
a source is plugged in (guitar, bass etc.) and as channel 1
output when an amp or an effect is plugged in.
A1 & B1:
these 1/4" TS jacks serve as channel 1 outputs
when amps or effects are plugged in; they serve as channel
1 inputs when instruments are plugged in. Only one of
these connectors can be active at any one time.
LATCH/NON LATCH:
this selector determines the channel
switch function: when set to LATCH, the switch is latching.
When set to NON LATCH, the signal will only be routed to or
from B1 as long as you hold the pedal depressed.
4
Fig. 1.2: Top view
SWITCH 1:
this switch allows you to assign the IN/OUT 1
signal to A1 or B1 when IN/OUT 1 is used as an input.
Otherwise, the switch assigns the A1 or B1 signal to
IN/OUT 1 when A1 and B1 are used as inputs. The A1 and
B1 LEDs display which connector is currently active.
Depending on the selector
position, shortly press the
switch (LATCH) or hold it down during the whole commutation
time (NON LATCH) to toggle between A1 and B1.
To install or replace the 9 V battery, please carefully unscrew the
bottom plate and open the enclosure of the AB200. After installing
close the unit again by using all screws you removed before.
+
The AB200 has no on/off switch. As soon as you
insert a jack into the A1 or B1 connector, the AB200
begins running. When not using the AB200, remove
the jacks from the connectors. This extends the
life of the battery.
The
SERIAL NUMBER
is located at the bottom of the unit.
2. APPLICATIONS
Fig. 2.1: One instrument / two amps
Plug your instrument into IN/OUT 1 and the input of each amp
into one of the A1 and B1 connectors. Pressing the switch 1 will
toggle between the two amps.
Fig. 2.2: Two instruments / one amp
Plug each of your instruments into one of the A1 and B1
connectors and the amp input into IN/OUT 1. Pressing the switch
1 will toggle between the two instruments.