Behringer FOUR PLAY Quick Start Guide - Page 10

Power Connection, Installation

Get Behringer FOUR PLAY PDF manuals and user guides View all Behringer FOUR PLAY manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

18 FOUR PLAY Power Connection P1 21 10 9 Red Stripe 200 mm ± 10 Connect end P1 to the module socket Connect end P2 to the power supply P2 12 15 16 HOT USED + 12V GROUND - 12V + 12V GROUND - 12V The Four Play module comes with the required power cable for connecting to a standard Eurorack power supply system. Follow these steps to connect power tothe module. It is easier to make these connections before the module has been mounted into a rack case. 1. Turn the power supply or rack case power off and disconnect the power cable. 2. Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable. 3. Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for correct orientation. 4. After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply. Quick Start Guide 19 Installation The necessary screws are included with the module for mounting in a Eurorack case. Connect the power cable before mounting. Depending on the rack case, there may be a series of fixed holes spaced 2 HP apart along the length of the case, or a track that allows individual threaded plates to slide along the length of the case. The free-moving threaded plates allow precise positioning of the module, but each plate should be positioned in the approximate relation to the mounting holes in your module before attaching the screws. Hold the module against the Eurorack rails so that each of the mounting holes are aligned with a threaded rail or threaded plate. Attach the screws part way to start, which will allow small adjustments to the positioning while you get them all aligned. After the final position has been established, tighten the screws down.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
Power Connection
The Four Play module comes with the required
power cable for connecting to a standard Eurorack
power supply system. Follow these steps to
connect power tothe module. It is easier to make
these connections before the module has been
mounted into a rack case.
1.
Turn the power supply or rack case power off
and disconnect the power cable.
2.
Insert the 16-pin connector on the power cable
into the socket on the power supply or rack
case. The connector has a tab that will align
with the gap in the socket, so it cannot be
inserted incorrectly. If the power supply does
not have a keyed socket, be sure to orient pin 1
(-12 V) with the red stripe on the cable.
3.
Insert the 10-pin connector into the socket on
the back of the module. The connector has a
tab that will align with the socket for correct
orientation.
4.
After both ends of the power cable have been
securely attached, you may mount the module
in a case and turn on the power supply.
HOT USED
Red Stripe
200 mm ± 10
15
16
2
1
P2
P1
2
10
9
1
Connect end P1 to the module socket
Connect end P2 to the power supply
+ 12V
- 12V
GROUND
+ 12V
- 12V
GROUND
Installation
The necessary screws are included with the
module for mounting in a Eurorack case. Connect
the power cable before mounting.
Depending on the rack case, there may be a series
of fixed holes spaced 2 HP apart along the length
of the case, or a track that allows individual
threaded plates to slide along the length of the
case. The free-moving threaded plates allow
precise positioning of the module, but each plate
should be positioned in the approximate relation
to the mounting holes in your module before
attaching the screws.
Hold the module against the Eurorack rails so
that each of the mounting holes are aligned with
a threaded rail or threaded plate. Attach the
screws part way to start, which will allow small
adjustments to the positioning while you get
them all aligned. After the final position has been
established, tighten the screws down.
19
Quick Start Guide
18
FOUR PLAY