Behringer MINIMON MON800 Manual - Page 9

Rear panel

Get Behringer MINIMON MON800 PDF manuals and user guides View all Behringer MINIMON MON800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

9 MINIMON MON800 User Manual (12) The TALK TO CUE/PHONES/SPK A and TALK TO 2-TR OUT buttons determine where the talk-back microphone signal is routed to. With the TALK TO CUE/PHONES/SPK A button the signal is routed to the monitor paths CUE OUT, PHONES, PH and SPEAKERS OUT A. In this case, the DIM function (9) is activated automatically to avoid feedback. The TALK TO 2-TR OUT button allows you to route the signal via the two 2-TRACK OUT outputs to the recording devices connected. ◊ Hold the button down as long as you wish to speak. 3.2 Rear panel (15) (13) The switch turns your MINIMON MON800 on and off. ◊ Attention: The switch does not fully disconnect the unit from the mains. To disconnect the unit from the mains, pull out the main cord plug or appliance coupler. When installing the product, ensure the plug or appliance coupler is readily operable. Unplug the power cord completely when the unit is not used for prolonged periods of time. (14) (16) (17) (18) (19) (20) (21) (22) Fig. 3.2: Rear panel connectors of the MON800 (14) The MON800 is connected to the mains using a 2-pole POWER connector jack. A matching mains adaptor is included with the unit. ◊ To avoid damage to your COM800 always use the mains adaptor supplied with the unit. (15) A second pair of headphones can be connected to the PH jack. This connector is wired in parallel with the front-panel jack (3). (16) The TB jack is used to connect a single footswitch. This footswitch allows hands-free talking and the use of the talk-back button (12) (TALK TO CUE/PHONES/SPK A) at the same time. ◊ Hold the button down as long as you wish to speak. (17) Two pairs of loudspeakers can be connected to the SPEAKERS OUT B and C jacks. Since the levels of both pairs (B and C) can only be adjusted together on the MON800, it's a good idea to connect one speaker pair to output B and an additional sub-woofer to output C (see chapter 4.1). (18) Connect your main monitor speakers to the SPEAKERS OUT A jack. ◊ The loudspeaker outputs are designed for the connection of active systems or an external amplifier with passive speakers. (19) CUE OUT is an additional output, which you can use to route the MINIMON signals to other devices, such as an additional headphones amp (e.g. BEHRINGER MINIAMP AMP800) (see chapter 4.1). ◊ The CUE OUT level cannot be changed on the MON800. (20) The two 2-TRACK OUT jacks are wired in parallel and carry the same signals. Use the 1/4" or cinch outputs, depending on the recording device used. (21) Use the CD/TAPE IN jacks C and D to connect playback devices, such as a computer, CD/MD or cassette player. (22) The MIX IN jacks A and B are for connecting the main signal sources (e.g. mixing console, audio card, etc.) using 1/4" plugs. Mono signals must be connected to the L jacks. The SERIAL NUMBER of your MON800 can be found on the bottom side of the unit.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
9
MINIMON MON800 User Manual
(12)
The
TALK TO CUE/PHONES/SPK A
and
TALK TO 2-TR OUT
buttons determine where the talk-back microphone signal is
routed to. With the
TALK TO CUE/PHONES/SPK A
button the
signal is routed to the monitor paths CUE OUT, PHONES, PH and
SPEAKERS OUT A. In this case, the DIM function
(9)
is activated
automatically to avoid feedback. The TALK TO 2-TR OUT button
allows you to route the signal via the two 2-TRACK OUT outputs
to the recording devices connected.
◊
Hold the button down as long as you wish to speak.
(13)
The
switch turns your MINIMON MON800 on and off.
◊
Attention: The
switch does not fully disconnect
the unit from the mains. To disconnect the unit from
the mains, pull out the main cord plug or appliance
coupler. When installing the product, ensure the plug or
appliance coupler is readily operable. Unplug the power
cord completely when the unit is not used for prolonged
periods of time.
3.2
Rear panel
(14)
(17)
(16)
(15)
(18)
(19)
(20)
(21)
(22)
Fig. 3.2: Rear panel connectors of the MON800
(14)
The MON800 is connected to the mains using a 2-pole
POWER
connector jack. A matching mains adaptor is included with
the unit.
◊
To avoid damage to your COM800 always use the mains
adaptor supplied with the unit.
(15)
A second pair of headphones can be connected to the
PH
jack.
This connector is wired in parallel with the front-panel jack
(3)
.
(16)
The
TB
jack is used to connect a single footswitch.
This footswitch allows hands-free talking and the use of the
talk-back button
(12)
(TALK TO CUE/PHONES/SPK A) at the
same time.
◊
Hold the button down as long as you wish to speak.
(17)
Two pairs of loudspeakers can be connected to the
SPEAKERS OUT
B and C jacks. Since the levels of both pairs
(B and C) can only be adjusted together on the MON800, it’s a
good idea to connect one speaker pair to output B and an
additional sub-woofer to output C (see chapter 4.1).
(18)
Connect your main monitor speakers to the
SPEAKERS OUT A
 jack.
◊
The loudspeaker outputs are designed for the
connection of active systems or an external amplifier
with passive speakers.
(19)
CUE OUT
is an additional output, which you can use to route
the MINIMON signals to other devices, such as an additional
headphones amp (e.g. BEHRINGER MINIAMP AMP800)
(see chapter 4.1).
◊
The CUE OUT level cannot be changed on the MON800.
(20)
The two
2-TRACK OUT
jacks are wired in parallel and carry the
same signals. Use the °" or cinch outputs, depending on the
recording device used.
(21)
Use the
CD/TAPE IN
jacks
C
and
D
to connect playback devices,
such as a computer, CD/MD or cassette player.
(22)
The
MIX IN
jacks
A
and
B
are for connecting the main signal
sources (e.g. mixing console, audio card, etc.) using °" plugs.
Mono signals must be connected to the
L
jacks.
The
SERIAL NUMBER
of your MON800 can be found on the bottom
side of the unit.