Behringer PS400 Manual - Page 1

Behringer PS400 Manual

Get Behringer PS400 PDF manuals and user guides View all Behringer PS400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

MICROPOWER PS400 Welcome to BEHRINGER Thank you for showing your confidence in us by purchasing the BEHRINGER MICROPOWER PS400. Use this ultra-compact phantom power supply with mixers and microphone preamplifiers that do not include phantom power sources. The PS400: • supplies phantom power (+12 V or +48 V) to any type of condenser microphone • routes the microphone signal to a mixer or a microphone preamplifier ◊ Please read the safety instructions that appear at the end of this document. Connectors and Control Elements This section illustrates and describes each PS400 connector and control element. (1) (3) (4) (5) (5) +12 V / +48 V PHANTOM VOLTAGE switch: To select the voltage that you need, push this switch toward +12 V or, alternatively +48 V. For details about what value to use, refer to instructions from the microphone manufacturer. SERIAL NUMBER: To register the unit, use the serial number that is located on the bottom of the PS400. Setup Example The following is an example of how to set up the PS400: STUDIO CONDENSER MICROPHONE C-1 MIC INPUT PROMIXER DJX750 MIC THRU (2) Fig. 1: PS400 connectors and control elements (1) 12 V� connector: To connect the power supply unit to the PS400, use the 12 V connector. Connecting the power supply unit to the mains automatically switches the PS400 on. To disconnect the unit from the mains, pull out the main cord plug. (2) ON LED: As soon as the unit is connected to the mains, the ON LED is illuminated. (3) MIC INPUT connector: To send a microphone signal to the PS400, you need an audio cable that includes XLR connectors. Plug: • one XLR connector into the MIC INPUT connector • the other XLR connector into the condenser microphone (4) MIC THRU connector: To route the microphone signal from the PS400 to a mixer or a microphone preamplifier, you need an audio cable that includes XLR connectors. Plug: • one XLR connector into the MIC THRU connector • the other XLR connector into the mic input of a mixer or, alternatively a microphone preamplifier Fig. 2: PS400 setup example MICROPOWER PS400 Warranty For the applicable warranty terms and conditions and additional information regarding MUSIC Group's Limited Warranty, please see complete details online at www.music-group.com/warranty.

  • 1
  • 2
MICROPOWER PS400
Welcome to BEHRINGER
Thank you for showing your confidence in us by purchasing the BEHRINGER MICROPOWER
PS400. Use this ultra-compact phantom power supply with mixers and microphone
preamplifiers that do not include phantom power sources. The PS400:
•
supplies phantom power (+12 V or +48 V) to any type of condenser microphone
•
routes the microphone signal to a mixer or a microphone preamplifier
◊
Please read the safety instructions that appear at the end of this document.
Connectors and Control Elements
This section illustrates and describes each PS400 connector and control element.
(2)
(1)
(3)
(4)
(5)
Fig. 1: PS400 connectors and control elements
(1)
12 V
�
connector:
To connect the power supply unit to the PS400, use the 12 V connector. Connecting the
power supply unit to the mains automatically switches the PS400 on. To disconnect
the unit from the mains, pull out the main cord plug.
(2)
ON
LED:
As soon as the unit is connected to the mains, the ON LED is illuminated.
(3)
MIC INPUT
connector:
To send a microphone signal to the PS400, you need an audio cable that includes XLR
connectors. Plug:
•
one XLR connector into the MIC INPUT connector
•
the other XLR connector into the condenser microphone
(4)
MIC THRU
connector:
To route the microphone signal from the PS400 to a mixer or a microphone
preamplifier, you need an audio cable that includes XLR connectors. Plug:
•
one XLR connector into the MIC THRU connector
•
the other XLR connector into the mic input of a mixer or, alternatively a
microphone preamplifier
(5)
+12 V / +48 V PHANTOM VOLTAGE
switch:
To select the voltage that you need, push this switch toward +12 V or, alternatively
+48 V. For details about what value to use, refer to instructions from the
microphone manufacturer.
SERIAL NUMBER
: To register the unit, use the serial number that is located on the bottom
of the PS400.
Setup Example
The following is an example of how to set up the PS400:
MICROPOWER PS400
PROMIXER DJX750
STUDIO CONDENSER
MICROPHONE C-1
MIC THRU
MIC INPUT
Fig. 2: PS400 setup example
Warranty
For the applicable warranty terms and conditions and additional information
regarding MUSIC Group’s Limited Warranty, please see complete details online at
www.music-group.com/warranty.