Behringer UB2222FX-PRO User Manual - Page 9

EURORACK UB1622FX-PRO/UB1832FX-PRO/UB2222FX-PRO/UB2442FX-PRO Using the STEREO AUX RETURN (TO AUX SEND) control, the effect signal can now be blended into the monitor mix. You can easily use the headphones distribution amplifier BEHRINGER POWERPLAY PRO HA4700/HA8000 to provide four (HA8000: eight) stereo headphone mixes for your studio. The following table shows which jacks on the console can be used for this purpose. Fig. 2.11: Monitor fader of the UB1832FX-PRO MUTE Press the MUTE switch to mute the monitor send. SOLO The SOLO switch routes the monitor send to the solo bus (post-fader and post-mute) or to the PFL bus (pre-fader and pre-mute). The position of the MODE switch in the main section determines which of the buses is selected. 2.3.5 Stereo aux return control STEREO AUX RETURN 1 The STEREO AUX RETURN 1 control determines the level of this signal in the main mix. If STEREO AUX RETURN 1 is used as effects return, this will determine the level of the effects when mixed with any “dry” channel signal. + When used in this way, the effects device should be set at 100% effect. Fig. 2.12: Stereo aux return and stereo aux return (to aux send) controls STEREO AUX RETURN 1/2 (TO AUX SEND) The two right-hand STEREO AUX RETURN controls have a special function: they can be used to add an effect to a monitor mix. An example follows (UB1622FX-PRO wired to an effects device): Monitor mix with effect In this instance, your effects device should be set up as follows: the AUX SEND 2 jack should be connected to the L/Mono input of your effects device, with its outputs coming back into the STEREO AUX RETURN 1 jacks. Connect the AUX SEND 1 jack output to the amplifier of your monitor system. The AUX SEND 1 master control determines the overall volume of the monitor mix. @‘‡r…hyÃrssrp‡†Ã qr‰vprÃ…rprv‰r†Ã †vthyÃs…‚€ à AUX SEND ! AUX SEND @‘‡r…hyÃrssrp‡†Ã UurÃrssrp‡Ã†vthyà qr‰vprÃ…‚ˆ‡r†Ã†vthyà …rhpur†Ã‡urÀ‚v‡‚…à ihpxÇ‚ €v‘Évh  « V7 %!!AYQSP STEREO AUX RETURN à connectors V7 '"!AYQSP STEREO AUX RETURN (TO AUX SEND ) control STEREO AUX RETURN !à connectors V7!!!!AYQSP MONITOR switch of the FX/AUXÃ! RET AUX SENDÃ! AUX SEND ! AUX SENDà STEREO AUX STEREO AUX RETURN connectors RETURN Ã(TO AUX Â…Ã! SEND ) control V7!##!AYQSP STEREO AUX RETURN à connectors ‚ƒ‡v‚hy) STEREO AUX RETURN !à connectors STEREO AUX RETURN (TO AUX SEND ) control STEREO AUX RETURN ! (TO AUX SEND !) control Tab. 2.1: Connectors and controls for monitor mix with effect STEREO AUX RETURN FX On consoles UB1622FX-PRO and UB1832FX-PRO this is the STEREO AUX RETURN 2, on consoles UB2222FX-PRO and UB2442FX-PRO this is the STEREO AUX RETURN 3. Use the STEREO AUX RETURN FX control to determine the level of the signal routed from the AUX RETURN FX jacks to the main mix. If nothing is connected to these jacks, the output of the built-in effects module will appear. MAIN MIX / TO SUBS This switch routes the signal fed in via the STEREO AUX RETURN FX jacks either to the main mix (not pressed) or to the submix (pressed). On the UB2442FX-PRO you can select which subgroup the signal is assigned to (switches 1-2 / 3-4, to the right of MAIN MIX / TO SUBS). SOLO RETURNS Additionally, this model allows you to route the aux returns together to the solo bus and the PFL bus. The LED lights up when Solo is on. STEREO AUX RETURN 4 (UB2442FX-PRO only) This control behaves the same way as the other stereo aux returns. Additionally, it provides for a simple monitor path using the switch CTRL ROOM & PHONES ONLY. CTRL ROOM & PHONES ONLY Use this switch to route the signal appearing at the AUX RETURN 4 jacks to the control room and headphones outputs. 2.3.6 Supplement to UB1832FX-PRO The UB1832FX-PRO has a stereo fader for the AUX RETURN FX and offers a variety of routing options: MUTE disables the effect return (but not PFL of course!), SOLO routes it to the Solo or PFL busses, SUB to the subgroups and MAIN to the main mix. 2. CONTROL ELEMENTS AND CONNECTORS 9