Behringer ULTRA SHIFTER/HARMONIST US600 User Manual - Page 2

Safety Instructions, Warranty, Specifications - manual

Page 2 highlights

ULTRA SHIFTER/HARMONIST US600 (9) The two 1/4" TS OUT A and OUT B connectors send the signal to your amp. If both outputs are used they will output different signals in the modes Pitch Shifter, Harmonist and Detune. OUT A will have the pitch shifted signal while OUT B will have the input signal. The volume of both outputs will be effected by the BALANCE control. In Trem Bar and Flutter mode both outputs will have the pitch shifted signal. (10) Use the 1/4" TRS EXP/CTL connector to connect an expression pedal. Set the pedal to the lowest position when connecting it to the unit. Then push it to the forward position and choose the desired pitch value with the PITCH control. Now you can control the pitch value of the effect within the range defined by the PITCH control (low position = no pitch shift, forward position = maximum pitch shift). Use the DC IN connection at the front of the unit to plug in a 9 V power supply (not included). The BATTERY COMPARTMENT is located underneath the pedal cover. To install or replace the 9 V battery (not included), press the hinges with a ballpoint pen and remove the pedal cover. Be careful not to scratch the unit. ◊ The US600 has no on/off switch. As soon as you insert the plug into the in connector, the US600 begins running. When not using the US600, remove the plug from the in connector. This extends the life of the battery. The SERIAL NUMBER is located at the underside. ◊ In rare cases interferences of the normal function may appear by external influence (e.g. electrostatic discharge), as for example sound disturbances or malfunctions. If this occurs, please turn down the volume on subsequent amplifiers and disconnect the input connector briefly to restart the application. 2. Safety Instructions Do not use near water, or install near heat sources. Use only authorized attachments/accessories. Do not service product yourself. Contact our qualified servicing personnel for servicing or repairs, especially when power supply cord or plug is damaged. 3. Warranty Please register your new BEHRINGER equipment right after your purchase by visiting http://behringer.com and read the terms and conditions of our warranty carefully. 4. Specifications In A Connector Impedance 1/4" TS 500 kΩ Out A Connector 1/4" TS Impedance 1 kΩ Out B Connector 1/4" TS Impedance 1 kΩ Power Supply 9 V, 100 mA regulated BEHRINGER PSU-SB U.S.A./Canada 120 V~, 60 Hz China 220 V~, 50 Hz Korea 220 V~, 60 Hz Europe/U.K./Australia 230 V~, 50 Hz Japan 100 V~, 50/60 Hz Power connector 2 mm DC jack, negative center Battery 9 V type 6LR61 Power consumption 30 mA Physical/Weight Dimensions (H x W x D) Weight approx. 2 1/8 x 2 3/4 x 4 4/5" approx. 54 x 70 x 123 mm approx. 0.73 lbs / 0.33 kg BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may therefore differ from those listed or shown. TECHNICAL SPECIFICATIONS AND APPEARANCES ARE SUBJECT TO CHANGE WITHOUT NOTICE AND ACCURACY IS NOT GUARANTEED. BEHRINGER, KLARK TEKNIK, MIDAS, BUGERA, AND TURBOSOUND ARE PART OF THE MUSIC GROUP (MUSIC-GROUP.COM).. ALL TRADEMARKS ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS. MUSIC GROUP ACCEPTS NO LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED BY ANY PERSON WHO RELIES EITHER WHOLLY OR IN PART UPON ANY DESCRIPTION, PHOTOGRAPH OR STATEMENT CONTAINED HEREIN. COLORS AND SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT. MUSIC GROUP PRODUCTS ARE SOLD THROUGH AUTHORIZED FULLFILLERS AND RESELLERS ONLY. FULLFILLERS AND RESELLERS ARE NOT AGENTS OF MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIED UNDERTAKING OR REPRESENTATION. THIS MANUAL IS COPYRIGHTED. NO PART OF THIS MANUAL MAY BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRONIC OR MECHANICAL, INCLUDING PHOTOCOPYING AND RECORDING OF ANY KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS WRITTEN PERMISSION OF MUSIC GROUP IP LTD. ALL RIGHTS RESERVED. © 2013 MUSIC Group IP Ltd. Trident Chambers, Wickhams Cay, P.O. Box 146, Road Town, Tortola, British Virgin Islands

  • 1
  • 2
  • 3

ULTRA SHIFTER/HARMONIST US600
TECHNICAL SPECIFICATIONS AND APPEARANCES ARE SUBJECT TO CHANGE WITHOUT NOTICE AND ACCURACY IS NOT GUARANTEED. BEHRINGER, KLARK TEKNIK,
MIDAS, BUGERA, AND TURBOSOUND ARE PART OF THE MUSIC GROUP (MUSIC-GROUP.COM).. ALL TRADEMARKS ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS.
MUSIC GROUP ACCEPTS NO LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED BY ANY PERSON WHO RELIES EITHER WHOLLY OR IN PART UPON ANY DESCRIPTION,
PHOTOGRAPH OR STATEMENT CONTAINED HEREIN. COLORS AND SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT. MUSIC GROUP PRODUCTS ARE SOLD THROUGH
AUTHORIZED FULLFILLERS AND RESELLERS ONLY. FULLFILLERS AND RESELLERS
ARE NOT AGENTS OF MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY TO BIND
MUSIC GROUP BY ANY EXPRESS OR IMPLIED UNDERTAKING OR REPRESENTATION. THIS MANUAL IS COPYRIGHTED. NO PART OF THIS MANUAL MAY BE REPRODUCED
OR TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRONIC OR MECHANICAL, INCLUDING PHOTOCOPYING AND RECORDING OF ANY KIND, FOR ANY PURPOSE,
WITHOUT THE EXPRESS WRITTEN PERMISSION OF MUSIC GROUP IP LTD. ALL RIGHTS RESERVED. © 2013 MUSIC Group IP Ltd. Trident Chambers, Wickhams Cay,
P.O. Box 146, Road Town, Tortola, British Virgin Islands
(9)
The two °" TS OUT A and OUT B connectors send the signal to your amp. If both outputs are used they will
output different signals in the modes Pitch Shifter, Harmonist and Detune. OUT A will have the pitch shifted
signal while OUT B will have the input signal. The volume of both outputs will be effected by the BALANCE
control. In Trem Bar and Flutter mode both outputs will have the pitch shifted signal.
(10)
Use the °" TRS EXP/CTL connector to connect an expression pedal. Set the pedal to the lowest position when
connecting it to the unit. Then push it to the forward position and choose the desired pitch value with the
PITCH control. Now you can control the pitch value of the effect within the range defined by the PITCH control
(low position = no pitch shift, forward position = maximum pitch shift).
Use the
DC IN
connection at the front of the unit to plug in a 9 V power supply (not included).
The
BATTERY COMPARTMENT
is located underneath the pedal cover. To install or replace the 9 V battery
(not included), press the hinges with a ballpoint pen and remove the pedal cover. Be careful not to scratch the unit.
The US600 has no on/off switch. As soon as you insert the plug into the in connector, the US600 begins
running. When not using the US600, remove the plug from the in connector. This extends the life of
the battery.
The
SERIAL NUMBER
is located at the underside.
In rare cases interferences of the normal function may appear by external influence (e.g. electrostatic
discharge), as for example sound disturbances or malfunctions. If this occurs, please turn down the
volume on subsequent amplifiers and disconnect the input connector briefly to restart the application.
2.
Safety Instructions
Do not use near water, or install near heat sources. Use only authorized attachments/accessories. Do not service
product yourself. Contact our qualified servicing personnel for servicing or repairs, especially when power supply
cord or plug is damaged.
3.
Warranty
Please register your new BEHRINGER equipment right after your purchase by visiting http://behringer.com
and read the terms and conditions of our warranty carefully.
4.
Specifications
In A
Connector
°" TS
Impedance
500 kΩ
Out A
Connector
°" TS
Impedance
1 kΩ
Out B
Connector
°" TS
Impedance
1 kΩ
Power Supply
9 V
°
, 100 mA regulated
BEHRINGER PSU-SB
U.S.A./Canada
120 V~, 60 Hz
China
220 V~, 50 Hz
Korea
220 V~, 60 Hz
Europe/U.K./Australia
230 V~, 50 Hz
Japan
100 V~, 50/60 Hz
Power connector
2 mm DC jack,
negative center
Battery
9 V type 6LR61
Power consumption
30 mA
Physical/Weight
Dimensions
approx. 2 ±²8 x 2 ³ x 4 ´²µ"
(H x W x D)
approx. 54 x 70 x 123 mm
Weight
approx. 0.73 lbs / 0.33 kg
BEHRINGER is constantly striving to maintain the
highest professional standards. As a result of these efforts,
modifications may be made from time to time to existing
products without prior notice. Specifications and appearance
may therefore differ from those listed or shown.