Beko CCB6254 User Manual - Page 13

13 / 15

EN

Cooker Hood / User Manual

3

Operating your appliance

Replacing the halogen/incandescent

lamps (Fig.12):

Only use lamps of the same type and Wattage in-

stalled on the device.

Commands (Fig.11):

Push-button A =

On/off lights switch.

Push-button B =

On/off cooker hood switch.

The appliance switches on at speed level 1, If the

cooker hood is on depress the push-button for 2

sec. to switch off the cooker hood. If the cooker

hood is at speed level 1 it will not be necessary

to depress the push-button to switch the cooker

hood off. Decreases the motor speed.

Display C =

Indicates the motor speed level se-

lected and activates the timer.

Push-button D =

Switches on the cooker hood.

Increases the motor speed. Touching the key at

3rd speed, the intensive function runs for 10’,

then the appliance go back to work at the original

speed. During this function the display blinks.

Key E =

The Timer times the functions on activa-

tion for 15 minutes, after which they are switched

off. The Timer is deactivated by re-pressing

Key

E.

When the Timer is activated the decimal point

must flash on the display. The Timer cannot be ac-

tivated if the intensive speed is functioning.

The

“clean air”

function is activated by press-

ing key

E

for 2 seconds when the appliance is

switched off.

This switches the motor on for 10 minutes every

hour at the first speed.

During functioning a rotary movement of the pe-

ripheral segments must be visualised on the dis-

play. When this time has passed the motor switch-

es off and the fixed letter

“C”

must be visualised

on the display until the motor re-starts after 50

minutes for another 10 minutes and so on. Press

any key apart from the light keys to return to nor-

mal functioning. Press key

E

to deactivate the

function.

Anti-grease/active charcoal filters

saturation:

•

When display item

C

flashes, at a speed where

it alternates with the letter

F

(e.g.

1

and

F

), the

grease filters must be washed.

•

When display item

C

flashes, at a speed where

it alternates with the letter

A

(e.g.

1

and

A

), the

active carbon filters must be replaced or washed

depending on the type of filter.

After the clean filter has been positioned correctly,

the electronic memory must be reset by pressing

button

A

for approximately

5 seconds

, until the

indication

F

or

A

shown on the display

C

stops

flashing.

Commands luminous (Fig.9)

the key

symbols are explained below:

A

= LIGHT

B

= OFF

C

= SPEED I

D

= SPEED II

E

= SPEED III

F

= AUTOMATIC STOP TIMER - 15 minutes (*)

If your appliance does not have the

INTENSIVE

speed function, press key

E

for 2 seconds and it

will be activated for 10 minutes after which it will

return to the previously set speed. When the func-

tion is active the LED flashes. To interrupt it before

the 10 minutes have expired press key

E

again.

Some models allow activating this function even

with speed one and two.

By pressing key

F

for two seconds (with the hood

switched off) the

“clean air”

function is activat-

ed. This function switches the appliance on for ten

minutes every hour at the first speed. As soon as

this function is activated the motor starts up at the

first speed for ten minutes. During this time key

F

and key

C

must flash at the same time.

Beko CCB6254 User Manual - Page 13

Replacing the halogen/incandescent, lamps Fig.12, Commands Fig.11, Anti-grease/active charcoal

Page 13 highlights