Beko CIS55834 User Manual - Page 14

between the door seal and

Get Beko CIS55834 PDF manuals and user guides View all Beko CIS55834 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

12. Reposition left hand side feet on the opposite side.(10) Unscrew and remove the bottom door hinge pin bushing/door stopper using a cross-headed screwdriver. (11)Unscrew and remove the upper door middle hinge pin bushing/door stopper using a cross-headed screwdriver. IMPORTANT:This part cannot be used on the opposite side; left hand side middle hinge pin bushing/door stopper part is supplied in the plastic bag.(11) 13. Re-fit the upper hinge on the left hand side using flat-headed screwdriver.(12) 14. Fit upper door left hand side middle hinge pin bushing/door stopper supplied in the plastic bag using cross-headed screwdriver.(13) 15. Reposition three small plastic plugs on the left hand side, which are covering middle hinge holes, on the opposite side to cover holes left empty.(14) 16. Locate and re-fit upper door to upper hinge and hold the door firmly. (15) 17. Locate the middle hinge pin to middle hinge pin bushing of upper door on the left hand side and re-fit the middle hinge.(16) First fit the left screw when the door is closed and then fit the right screw after opening the door for access. 18. Reposition the screw fitted to lower hinge hole on the left hand side at the bottom of the cabinet on the opposite side.(17) 19. Locate and re-fit lower door to middle hinge pin and then re-fit the lower hinge on the left hand side. (18),(19) 20. Carefully stand the appliance upright and adjust the two front feet if necessary. 21. Check that doors open and close easily, they are aligned correctly and that there are no gaps allowing ir into the cabinet. If there are gaps between the door seal and the cabinet, adjust the door seal by gently pulling away from the door using fingers. 22. Check that all the hinge screws are tightened. Avoid over tightening the screws. 23. Put all items, fittings back in the appliance. 24. Fit upper door top trim and front top panel plastic hinge covers. Upper door top trim hinge covers are supplied in the plastic bag.(20) 25. Wait for at least 4 hours to allow the system to settle before switching on. 26. Once the correct storage temperatures have been reached in the appliance, put back all the food. Using the screws and plastic plugs supplied in the installation kit inside the fridge, fit handles to the desired side (see diagram P12 for locations) 13 EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
EN
13
12.
Reposition left hand side feet
on the opposite side.(10)
Unscrew and remove the bottom
door hinge pin bushing/door
stopper using a cross-headed
screwdriver. (11)Unscrew and
remove the upper door middle
hinge pin bushing/door stopper
using a cross-headed screwdriver.
IMPORTANT:
This part cannot be
used on the opposite side; left hand
side middle hinge pin bushing/door
stopper part is supplied in the plastic
bag.(11)
13.
Re-fit the upper hinge on the
left hand side using flat-headed
screwdriver.(12)
14.
Fit upper door left hand side
middle hinge pin bushing/door
stopper supplied in the plastic bag
using cross-headed screwdriver.(13)
15.
Reposition three small plastic
plugs on the left hand side, which are
covering middle hinge holes, on the
opposite side to cover holes left
empty.(14)
16.
Locate and re-fit upper door to
upper hinge and hold the door firmly.
(15)
17.
Locate the middle hinge pin
to middle hinge pin bushing of upper
door on the left hand side and re-fit
the
middle hinge.(16) First fit the
left screw when the door is closed
and then fit the right screw after
opening the door
for access.
18.
Reposition the screw fitted to
lower hinge hole on the left hand side
at the bottom of the cabinet on the
opposite side.(17)
19.
Locate and re-fit lower door
to middle hinge pin and then re-fit
the lower hinge on the left hand side.
(18),(19)
20.
Carefully stand the appliance
upright and adjust the two front feet
if necessary.
21.
Check that doors open and
close easily, they are aligned correctly
and that there are no gaps allowing
ir into the cabinet. If there are gaps
between the door seal and the
cabinet, adjust the door seal by gently
pulling away from the door using
fingers.
22.
Check that all the hinge screws
are tightened. Avoid over tightening
the screws.
23.
Put all items, fittings back in
the appliance.
24.
Fit upper door top trim and
front top panel plastic hinge covers.
Upper door top trim hinge covers are
supplied in the plastic bag.(20)
25.
Wait for at least 4 hours to
allow the system to settle before
switching on.
26.
Once the correct storage
temperatures have been reached in
the appliance, put back all the food.
Using the screws and plastic plugs
supplied in the installation kit inside
the fridge, fit handles to the desired
side (see diagram P12 for locations)