Beko DFN04C10 User Manual - Page 12

be earthed

Page 12 highlights

Installation must be min. 50 cm and max. 100 cm from the floor. A discharge hose longer than 4 meters will cause washing performance to be affected.Attach the water discharge hose to the drainpipe without bending it. Tightly fix the water discharge hose to the drainpipe in order to prevent any dislocation of the water discharge hose during operation of the product. C Drainpipe must be connected to the foul water system and it should not be connected to any surface water drain. Adjusting the feet If the door of the product cannot be closed properly or if the product wobbles when you push it slightly, then you need to adjust the feet of the product. Adjust the feet of the product as illustrated in the relevant section. Electrical connection Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating label corresponds to your electricity supply. 10 /36 EN max 1000 min 500 min 300 min 120 We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket in a readily accessible position. If the supply cord or the mains lead is damaged please do not replace it yourself. The supply cord or the mains lead must be replaced by a Authorised Service Agent or a similarly qualified person. A This appliance must be earthed If the fitted moulded plug is not suitable for your socket, then the plug should be cut off and an appropriate plug fitted. Destroy the old plug, which is cut off as a plug with a bared cord could cause a shock hazard if inserted into a socket elsewhere in the house. The moulded plug on this appliance incorporates a 13A fuse. Should the fuse need to be replaced an ASTA approved BS1362 fuse of the same rating must be used. Do not forget to refit the fuse cover. In the event of losing the fuse cover, the plug must not be used until a replacement fuse cover has been fitted. Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug. Fuse covers are available from any good electrical store. Dishwasher / User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38

10
Dishwasher / User’s Manual
/36 EN
Installation
must be min. 50 cm and max. 100 cm from
the floor. A discharge hose longer than 4
meters will cause washing performance
to be affected.Attach the water discharge
hose to the drainpipe without bending it.
Tightly fix the water discharge hose to the
drainpipe in order to prevent any dislocation
of the water discharge hose during
operation of the product.
min
300
min
120
max 1000
min 500
C
Drainpipe must be connected
to the foul water system and it
should not be connected to any
surface water drain.
Adjust±ng the feet
If the door of the product cannot be closed
properly or if the product wobbles when
you push it slightly, then you need to adjust
the feet of the product. Adjust the feet of
the product as illustrated in the relevant
section.
Electr±cal connect±on
Before you insert the plug into the wall
socket make sure that the voltage and
the frequency shown in the rating label
corresponds to your electricity supply.
We recommend that this appliance be
connected to the mains supply via a
suitable switched and fused socket in a
readily accessible position.
If the supply cord or the mains lead is
damaged please do not replace it yourself.
The supply cord or the mains lead must be
replaced by a Authorised Service Agent or a
similarly qualified person.
A
Th±s appl±ance must
be earthed
If the fitted moulded plug is not
suitable for your socket, then
the plug should be cut off and
an appropriate plug fitted.
Destroy the old plug, which is
cut off as a plug with a bared
cord could cause a shock
hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this
appliance incorporates a 13A
fuse. Should the fuse need to
be replaced an ASTA approved
BS1362 fuse of the same rating
must be used. Do not forget
to refit the fuse cover. In the
event of losing the fuse cover,
the plug must not be used
until a replacement fuse cover
has been fitted. Colour of the
replacement fuse cover must be
the same colour as that visible
on the pin face of the plug. Fuse
covers are available from any
good electrical store.