Beko HCB63744 User Manual - Page 10

Installation

Get Beko HCB63744 PDF manuals and user guides View all Beko HCB63744 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Installation Refer to the nearest Authorised Service Agent for installation of the product. Make sure that the electric installations are in place before calling the Authorised Service Agent to have the product ready for operation. If not, call a qualified electrician and fitter to have the required arrangements made. 0Preparation of location and electrical nstallation for the product is under customer's responsibility. Aa DANGER: 1 The product must be installed in accordance • with all local electrical regulations. AI DANGER: • Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety. An DANGER: Warning: Failure to install the screws or fixing device in accordance with the instructions may result in electrical hazards. Installation The exhaust air must not be discharged into a flue which is used for exhausting fumes from other appliances burning gas or other fuels. (Not applicable for appliances which only discharge air back into the room) Regulations concerning the discharge of air have to be fulfilled. Electrical connection Manufactured with 2-track power cable, this device must be connected to the mains by an electrical switch with at least 3mm clearance between bipolar contact leads. Have a qualified electrician to install electric wiring. • Install your product to ensure easy access to electricity connection (plug, wall outlet) after installation. Installing the hood Dimensions are given in mm. Information required for the preparation of the installation place for your hood is given below. Hood should be placed as aligned by the central axis of the cooking appliance. Cooking appliance and the hood's oil filters should be at least 650mm away from each other. Perform the following steps for the installation of the hood. E E E E o co co 7 * min. The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood is 65cm. 10/EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
Installation
Refer
to
the
nearest
Authorised
Service
Agent
for
installation
of
the
product.
Make
sure
that
the
electric
installations
are
in
place
before
calling
the
Authorised
Service
Agent
to
have
the
product
ready
for
operation.
If
not,
call
a
qualified
electrician
and
fitter
to
have
the
required
arrangements
made.
0
Preparation
of
location
and
electrical
nstallation
for
the
product
is
under
customer's
responsibility.
A
a
DANGER:
1
The
product
must
be
installed
in
accordance
•
local
with
all
electrical
regulations.
A
I
DANGER:
Prior
to
installation,
visually
check
if
the
•
has
defects
it.
product
any
on
If
so,
do
not
have
it
installed.
Damaged
products
cause
risks
for
your
safety.
A
n
DANGER:
Warning:
Failure
to
install
the
fixing
screws
or
device
in
accordance
with
the
instructions
may
result
in
electrical
hazards.
Installation
E
E
co
E
E
o
co
7
*
min.
The
minimum
distance
between
the
supporting
surface
for
the
cooking
vessels
on
the
hob and
the
lowest
part
of
the
range
hood
is
65cm.
The
exhaust
air
must
not
be
discharged
into
a
flue
which
is
used
for
exhausting
fumes
from
other
appliances
burning
gas
or
other
fuels.
(Not
applicable
for
appliances
which
only
discharge
air
back
into
the
room)
Regulations
concerning
the
discharge
of
air
have
to
be
fulfilled.
Electrical
connection
Manufactured
with
2
-track
power
cable,
this
device
must
be
connected
to
the
mains
by
an
electrical
switch
with
at
least
3mm
clearance
between
bipolar
contact
leads.
Have
a
qualified
electrician
to
install
electric
wiring.
•
Install
your
product
to
ensure
easy
access
to
electricity
connection
(plug,
wall
outlet)
after
installation.
Installing
the
hood
Dimensions
are
given
in
mm.
Information
required
for
the
preparation
of
the
installation
place
for
your
hood
is
given
below.
Hood
should
be
placed
as
aligned
by
the
central
axis
of
the
cooking
appliance.
Cooking
appliance
and
the
hood's
oil
filters
should
be
at
least
650mm
away
from
each
other.
Perform
the
following
steps
for
the
installation
of
the
hood.
10/EN