Beltronics Laser Pro 904 Installation Manual - Page 2

FRONT FRONT LASER MODULE FRONT LASER MODULE FIREWALL FIREWALL 3-PORT INTERFACE "HUB" C FR FIREWALL TO 12 VOLT POWER SUPPLY "Y" CONNECTOR REMOTE CONTROL DISPLAY BELTRONICS REAR 1. Control Display a) Determine an appropriate location to mount the control display based on visibility and customer input. b) Install the display using the hook and loop fastener. c) Plug the "pin" connectors to the back of the control display and the opposite end into the appropriate 3-port interface "hub". Installation sheet for LaserPro™ 904 Under Dash Mounting To mount the control display under the dash using the supplied under-dash bracket, drill two holes (#35, .110 diameter) to fasten the control display bracket with the two (2) black 3/8" self threading screws provided. Once installed, the control panel can slide into the bracket using the slots on each side of the unit. With a mounting location selected, plug the "pin" connectors to the back of the control display and the opposite end into the appropriate 3-port interface "hub". In-Dash Mounting The contol display can be mounted directly into the vehicle's dashboard. For this type of mounting, first select a flat location on the dash where there will be no interference with wires or components. *First, peel the back off the template provided and place over the selected area. *Drill two 3/16" diameter holes as indicated on the template and a third hole in the center of the cutout area to allow a saw blade to enter. Cut along the template outline. *Once the portion of the dash has been cut away, remove the template and insert the dash mount frame into the area and fasten to the dashboard using two (2) 3/4" black oval head screws with flat washers, lock washers and nuts on back side. Special notches allow the control display to be mounted into the 2 dash holder with varying lengths of the display exposed. NOTE: For in-dash mounting, do not install the control display into the dash until the front laser tranceivers and interface "hub" have been installed, and the cables have been routed through the in-dash mount. 2. Front Laser Transceivers a) Postion each of the two front Laser transceivers on either side of the front license plate. Many vehicles have open areas in the polyurethane bumpers in or around this area. If possible, choose an area between the license plate and the center point of headlight lens - see diagram (2) b) Using the mounting brackets supplied, mark the location and drill pilot holes if necessary. c) Mount the transceivers using the supplied hardware. NOTE: Both of the front transceivers must be level to the road. Use the supplied spirit level to ensure each transceiver is level to within +/- 5%. Align the spirit level along the etched line which appears at the side of each transceiver. 3 Finally, connect each jack from each transceiver to the "Y" connector provided. 3. Rear Laser Transceiver a) Remove the license plate screws from the license plate. b) Align the two holes in the rear Laser transceiver to the license plate; use supplied screws to re-attach. c) Route the wire emanating from the transceiver through the trunk compartment and into the vehicle's interior and up to the 3-hole interface "hub". Cable can also be routed under the vehicle, provided it is kept away from heat and moving parts. d) Insert the jack into the hole labeled "Rear Laser". NOTE: Ensure you do not block any information on the license plate. The cable may be cut if too long, however, it must be reconnected using solder for each of the three wires and sealed with heat-shrink tubing. 4. Routing of Front Laser Transceiver Cables a) Route the cable from the two front Laser transceivers to the vehicle's firewall, and secure with supplied tie-wraps. b) If a suitable opening in the firewall does not exist, drill a 13/32" or 7/16" hole to insert the cable. c) Pull the cable through the firewall, and plug into the jack marked Front Laser. d) Pull the grommet through the firewall to seal the hole. If necessary, use silicon sealant (not supplied). Note: Do not splice the cable. Ensure cable is kept away from any hot or moving parts. 5. 3-Port Interface "hub" a) Install the 3-hole interface under the vehicle's dash using the supplied tie-wraps. DO NOT MOUNT IN ENGINE COMPARTMENT. b) Connect black wire (-) to a ground source such as the vehicle's floor pan. Connect the red striped wire (+) to a switched 12-volt supply. Use the blue colored wire connector to tap into an existing circuit, if needed. Note: If LaserPro™ 904 is left in the "on" position, it will automatically power on and off with ignition. Testing Procedure After all components are installed correctly, turn LaserPro™ 904 ON by pressing the Power On button and turn the vehicle's ignition to the "on" position; LaserPro 904 will cycle through its startup test sequence. • DO NOT drill holes into the front Laser transceivers. • Make certain the area selected is suitable before drilling holes into the bumper. • Keep cables away from moving parts or hot or heated surfaces. BELTRONICS 12-18 ˝ 12-18 ˝ BELTRONICS • Do NOT splice the cables • Use the supplied spirit level to ensure that each transceiver is level.