BenQ BenQ HC1200 sRGB DLP Projector User Manual - Page 55

Timing of replacing the lamp, Status, Message

Get BenQ BenQ HC1200 sRGB DLP Projector PDF manuals and user guides View all BenQ BenQ HC1200 sRGB DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. Go to http://www.benq.com for a replacement lamp. The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the projector off and let the projector cool for 45 minutes. If the lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 59 for details. The following lamp warning displays will remind you to change the lamp. The warning messages below are for reference only. Please follow the actual on-screen instructions to prepare and replace the lamp. Status Message Install a new lamp for optimal performance. If the projector is normally run with Economic selected (See "Setting Lamp mode as Economic or SmartEco" on page 54), you may continue to operate the projector until the next lamp warning appears. Press MODE/ENTER to dismiss the message. It is strongly recommended that you replace the lamp at this age. The lamp is a consumable item. The lamp brightness diminishes with use. This is normal lamp behavior. You can replace the lamp whenever you notice that the brightness level has significantly diminished. Press MODE/ENTER to dismiss the message. The lamp MUST be replaced before the projector will operate normally. Press MODE/ENTER to dismiss the message. Maintenance 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Maintenance
55
Timing of replacing the lamp
When the
Lamp indicator
lights up red or a message appears suggesting it is time to
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
Go to
for a replacement lamp.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
hot. Turn the projector off and let the projector cool for 45 minutes. If the lamp or Temp
indicator still lights up after turning the power back on, please contact your dealer. See
"Indicators" on page 59
for details.
The following lamp warning displays will remind you to change the lamp.
The warning messages below are for reference only. Please follow the actual on-screen
instructions to prepare and replace the lamp.
Status
Message
Install a new lamp for optimal performance. If the
projector is normally run with
Economic
selected (See
"Setting Lamp mode as Economic or
SmartEco" on page 54
), you may continue to
operate the projector until the next lamp warning
appears.
Press
MODE/ENTER
to dismiss the message.
It is strongly recommended that you replace the
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished.
Press
MODE/ENTER
to dismiss the message.
The lamp MUST be replaced before the projector
will operate normally.
Press
MODE/ENTER
to dismiss the message.