BenQ MP512ST User Manual - Page 33

Using Wall Color, Fine-tuning the image quality in user modes, Setting the User 1/User 2 mode

Get BenQ MP512ST - DLP Short Throw Projector PDF manuals and user guides
UPC - 840046019600
View all BenQ MP512ST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Setting the User 1/User 2 mode There are two user-definable modes if the current available picture modes are not suitable for your need. You can use one of the picture modes (except the User 1/User 2) as a starting point and customize the settings. 1. Press Menu/Exit to open the On-Screen Display (OSD) menu. 2. Go to the PICTURE > Picture Mode menu. 3. Press / to select User 1 to User 2. 4. Press to highlight Reference Mode. This function is only available when User 1, or User 2 mode is selected up in the Picture Mode sub-menu item. 5. Press / to select an picture mode that is closest to your need. 6. Press to select a sub-menu item to be changed and adjust the value with / . See "Fine-tuning the image quality in user modes" below for details. 7. When all settings have been done, highlight Save Settings and press Mode/Enter to store the settings. 8. The confirmation message 'Setting Saved' displays. Using Wall Color In the situation where you are projecting onto a colored surface such as a painted wall which may not be white, the Wall Color feature can help correct the projected picture's color to prevent possible color difference between the source and projected pictures. To use this function, go to the DISPLAY > Wall Color menu and press / to select a color which is the closest to the color of the projection surface. There are several precalibrated colors to choose from: Light Yellow, Pink, Light Green, Blue, and Blackboard. Fine-tuning the image quality in user modes According to the detected signal type, there are some user-definable functions available when User 1 or User 2 mode is selected. You can make adjustments to these functions based on your needs. Adjusting Brightness Highlight Brightness in the PICTURE menu and adjust the values by pressing / on the projector or remote control. The higher the value, the brighter the image. And lower the setting, darker the image. Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible. +30 +50 +70 Adjusting Contrast Highlight Contrast in the PICTURE menu and adjust the values by pressing / on the projector or remote control. The higher the value, the greater the contrast. Use this to set the peak white level after you have previously adjusted the Brightness setting to suit your selected input and viewing environment. +30 +50 +70 Operation 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Operation
33
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable
for your need. You can use one of the picture modes (except the
User 1
/
User 2
) as a starting
point and customize the settings.
1.
Press
Menu/Exit
to open the On-Screen Display (OSD) menu.
2.
Go to the
PICTURE
>
Picture Mode
menu.
3.
Press
/
to select
User 1
to
User 2
.
4.
Press
to highlight
Reference Mode
.
This function is only available when User 1, or User 2 mode is selected up in the Picture Mode
sub-menu item.
5.
Press
/
to select an picture mode that is closest to your need.
6.
Press
to select a sub-menu item to be changed and adjust the value with
/
.
See
"Fine-tuning the image quality in user modes"
below for details.
7.
When all settings have been done, highlight
Save Settings
and press
Mode/Enter
to
store the settings.
8.
The confirmation message '
Setting Saved
' displays.
Using Wall Color
In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the
Wall Color
feature can help correct the projected picture’s color to
prevent possible color difference between the source and projected pictures.
To use this function, go to the
DISPLAY
>
Wall Color
menu and press
/
to select a
color which is the closest to the color of the projection surface. There are several
precalibrated colors to choose from:
Light Yellow
,
Pink
,
Light Green
,
Blue
, and
Blackboard
.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available
when
User 1
or
User 2
mode is selected. You can make adjustments to these functions based
on your needs.
Adjusting Brightness
Highlight
Brightness
in the
PICTURE
menu and adjust the values by pressing
/
on the
projector or remote control.
The higher the value, the brighter the image. And lower
the setting, darker the image. Adjust this control so the
black areas of the image appear just as black and that
detail in the dark areas is visible.
Adjusting Contrast
Highlight
Contrast
in the
PICTURE
menu and adjust the values by pressing
/
on the
projector or remote control.
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the
Brightness
setting to suit your selected
input and viewing environment.
+50
+30
+70
+50
+30
+70