BenQ MW811ST Short-Throw 3D Network Projector MX812ST User Manual - Page 41

Wireless connection, NETWORK SETTING, MENU/EXIT, SYSTEM SETUP: Advanced, ENTER, Wireless LAN

Get BenQ MW811ST Short-Throw 3D Network Projector PDF manuals and user guides View all BenQ MW811ST Short-Throw 3D Network Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Wireless connection To connect to the projector wirelessly, you have to plug a BenQ wireless dongle (optional) to the USB Type A connector on the projector, and then only a few OSD configuration steps are required. 1. Make sure the projector is turned on. 2. Do one of the following: • Press NETWORK SETTING on the remote control. The Network Settings page is displayed. • Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted. Press to highlight Network Settings and press MODE/ ENTER. The Network Settings page is displayed. 3. Highlight Wireless LAN and press MODE/ENTER. 4. Make sure the Status is Connect. 5. Make sure the SSID information is displayed. 6. Press to highlight Connection Mode and press / to select AP or Infrastructure. In AP mode, you need to use your computer's wireless connection utility to search the projector's SSID and connect to it. Then you can search the projector with Q Presenter. To use Infrastructure mode, you should connect both your computer and projector to the same AP router and make connections with the IP address. • There are more wireless settings available on the Projector Network display System > Admin > Wireless LAN page. • If you need more information about AP and Infrastructure modes, please refer to user documentations for Wireless Routers which are usually available on 3C stores. Operation 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
Operation
41
Wireless connection
To connect to the projector wirelessly, you have to plug a BenQ wireless dongle (optional) to
the USB Type A connector on the projector, and then only a few OSD configuration steps are
required.
1.
Make sure the projector is turned on.
2.
Do one of the following:
•
Press
NETWORK SETTING
on the remote control. The
Network Settings
page
is displayed.
•
Press
MENU/EXIT
and then press
/
until the
SYSTEM SETUP: Advanced
menu is highlighted. Press
to highlight
Network Settings
and press
MODE/
ENTER
. The
Network Settings
page is displayed.
3.
Highlight
Wireless LAN
and press
MODE/ENTER
.
4.
Make sure the
Status
is
Connect
.
5.
Make sure the
SSID
information is displayed.
6.
Press
to highlight
Connection Mode
and press
/
to select
AP
or
Infrastructure
.
In
AP
mode, you need to use your computer’s wireless connection utility to search the
projector’s SSID and connect to it. Then you can search the projector with Q
Presenter. To use
Infrastructure
mode, you should connect both your computer and
projector to the same AP router and make connections with the IP address.
•
There are more wireless settings available on the Projector Network display System >
Admin > Wireless LAN page.
•
If you need more information about AP and Infrastructure modes, please refer to user
documentations for Wireless Routers which are usually available on 3C stores.