BenQ MX813ST Short-Throw DLP Projector User Manual - Page 46

Shutting down the projector, Direct power off

Get BenQ MX813ST Short-Throw DLP Projector PDF manuals and user guides View all BenQ MX813ST Short-Throw DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Shutting down the projector 1. Press II on the projector. A confirmation message displays prompting you. If you don't respond in a few seconds, the message will disappear. If you use the remote control, press II to shut down the projector. 2. Press II on the projector a second time. The POWER indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run to cool down the projector. To protect the lamp, the projector will not respond to any commands during the cooling process. 3. Once the cooling process finishes, the POWER indicator light is a steady orange and fans stop. 4. Disconnect the power cord from the power putlet if the projector will not be used in an extended period of time. • If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press Power again to start the projector after the fans stop and the POWER indicator light turns orange. • Actual lamp lives may vary due to different environmental conditions and usage. Direct power off The AC power cord can be pulled out right after the projector is turned off. To protect the lamp, wait about 10 minutes before re-starting the projector. (When you attempt to re-start the projector, the fans may run for a few minutes to cool down. In such cases, press II again to start the projector after the fans stop and the POWER indicator light turns orange. 46 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Operation
46
Shutting down the projector
1.
Press
on the projector. A confirmation
message displays prompting you.
If you don't respond in a few seconds, the
message will disappear. If you use the remote
control, press
to shut down the projector.
2.
Press
on the projector a second time. The
POWER indicator light
flashes orange, the
projection lamp shuts down, and the fans will
continue to run to cool down the projector.
To protect the lamp, the projector will not respond to
any commands during the cooling process.
3.
Once the cooling process finishes, the
POWER indicator light
is a steady orange
and fans stop.
4.
Disconnect the power cord from the power putlet if the projector will not be used
in an extended period of time.
•
If the projector is not properly shut down, to protect the lamp, when you attempt to re-start
the projector, the fans will run for a few minutes to cool down. Press Power again to start
the projector after the fans stop and the POWER indicator light turns orange.
•
Actual lamp lives may vary due to different environmental conditions and usage.
Direct power off
The AC power cord can be pulled out right after the projector is turned off. To protect
the lamp, wait about 10 minutes before re-starting the projector. (When you attempt to
re-start the projector, the fans may run for a few minutes to cool down. In such cases,
press
again to start the projector after the fans stop and the POWER indicator light
turns orange.
I
I
I
I
I
I
I
I