BenQ RP552H Installation Handbook - Page 33

Setting, Advanced, OSD Rotation, Portrait, Screen, Display Wall, H. Monitors, H. Position

Get BenQ RP552H PDF manuals and user guides View all BenQ RP552H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Setting the display position in portrait mode If a video wall in portrait mode is desired, follow the procedures and refer to the matrix and examples for setup. 1. Rotate each display 90 degrees clockwise to install the video wall in portrait mode. 2. Rotate the picture 90 degrees counterclockwise from your video source (e.g. computer). 3. Rotate the OSD menu from each display. Go to Setting > Advanced > OSD Rotation and set it to Portrait. Alternatively, wait until the IR loop is created, then change the setting on one display to apply to all displays. See Management by remote control (selected models only) on page 35 for more information. 4. Go to Screen > Display Wall > H. Monitors and V. Monitors on each display to set the total number of displays counted vertically and horizontally. 5. Go to Screen > Display Wall > H. Position and V. Position on each display to set the position. The position is defined by the X-Y matrix. Starting from the top left of the video wall, the number increases as it goes down or goes to the right. X (Represented as H for horizontal position.) (H=1.V=1) (H+1.V=1) (H=1.V+1) (H+1.V+1) Y (Represented as V for vertical position.) Different video wall layouts and display position setup Set the display position carefully according to the video wall layout to ensure correct picture output. Following are some examples for your reference. (1.1) (2.1) (1.2) (2.2) (1.1) (2.1) (3.1) (1.1) (2.1) (3.1) (4.1) (1.2) (2.2) (3.2) (1.3) (2.3) (3.3) Video wall installation guide 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
33
Video wall installation guide
Setting the display position in portrait mode
If a video wall in portrait mode is desired, follow the procedures and refer to the matrix and
examples for setup.
1.
Rotate each display 90 degrees clockwise to install the video wall in portrait mode.
2.
Rotate the picture 90 degrees counterclockwise from your video source (e.g. computer).
3.
Rotate the OSD menu from each display. Go to
Setting
>
Advanced
>
OSD Rotation
and set it to
Portrait
. Alternatively, wait until the IR loop is created, then change the
setting on one display to apply to all displays. See
Management by remote control (selected
models only) on page 35
for more information.
4.
Go to
Screen
>
Display Wall
>
H. Monitors
and
V. Monitors
on each display to set
the total number of displays counted vertically and horizontally.
5.
Go to
Screen
>
Display Wall
>
H. Position
and
V. Position
on each display to set
the position. The position is defined by the X-Y matrix. Starting from the top left of the
video wall, the number increases as it goes down or goes to the right.
Different video wall layouts and display position setup
Set the display position carefully according to the video wall layout to ensure correct picture
output. Following are some examples for your reference.
(
H=
1.
V
=1)
(
H
+1.
V
=1)
(
H
+1.
V
+1)
(
H
=1.
V
+1)
Y
(Represented as V for vertical position.)
X
(Represented as H for horizontal
position.)
(1.1)
(2.1)
(2.2)
(1.2)
(1.1)
(2.1)
(3.1)
(4.1)
(1.3)
(1.2)
(1.1)
(2.3)
(2.2)
(2.1)
(3.3)
(3.2)
(3.1)