BenQ TL550 Large Display User Manual - Page 39

OSD Info Box, Reset User Default

Get BenQ TL550 PDF manuals and user guides View all BenQ TL550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

The OSD (On-Screen Display) menu 39 Power Save Sets the display to enter the power saving mode when there is no signal detected. • Eco: All source can enter the power saving mode, but only a VGA signal can wake up the display or you have to press the power button to wake up the display when other source is connected. • Standard: All source can enter the power saving mode and wake up the display. • Off: If no source is detected, the backlight will continue on. • VGA Only: Only the VGA signal can enter the power saving mode and wake up the display. Serial can bring any mode out of the power savings. Set Monitor Assigns an ID number for the current display when multiple displays are ID connected. Image Automatically displays swift moving patterns every 10 seconds to prevent image Retention retention on the screen. Auto Automatically optimizes image display for the VGA input. Adjustment Advanced • Reset User Default: Resets all OSD settings (except the Language setting) to the factory settings. • OSD Info Box: When turned ON, the display will always show the current input source and resolution onscreen. Select OFF to show the information box onscreen only when you press INFO on the remote control. • Status - Thermal: Shows current temperature inside the display. - Ambient Light: Shows current ambient brightness around the display. - 5V Detect: Shows the current 5V voltage detection result. - 12V Detect: Shows the current 12V voltage detection result. - Operating Time: Shows the time elapsed since the display was last turned on. D=Day, H=Hour. - FW Version: Shows the current firmware version. - Input Source: Shows the current input source and its resolution.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
The OSD (On-Screen Display) menu
39
Power
Save
Sets the display to enter the power saving mode when there is no signal
detected.
•
Eco
: All source can enter the power saving mode, but only a VGA signal can
wake up the display or you have to press the power button to wake up the
display when other source is connected.
•
Standard
: All source can enter the power saving mode and wake up the
display.
•
Off
: If no source is detected, the backlight will continue on.
•
VGA Only
: Only the VGA signal can enter the power saving mode and wake
up the display.
Serial can bring any mode out of the power savings.
Set Monitor
ID
Assigns an ID number for the current display when multiple displays are
connected.
Image
Retention
Automatically displays swift moving patterns every 10 seconds to prevent image
retention on the screen.
Auto
Adjustment
Automatically optimizes image display for the
VGA
input.
Advanced
•
Reset User Default
: Resets all OSD settings (except the Language setting)
to the factory settings.
•
OSD Info Box
: When turned
ON
, the display will always show the current
input source and resolution onscreen. Select
OFF
to show the information
box onscreen only when you press
INFO
on the remote control.
•
Status
-
Thermal
: Shows current temperature inside the display.
-
Ambient Light
: Shows current ambient brightness around the display.
-
5V Detect
: Shows the current 5V voltage detection result.
-
12V Detect
: Shows the current 12V voltage detection result.
-
Operating Time
: Shows the time elapsed since the display was last
turned on. D=Day, H=Hour.
-
FW Version
: Shows the current firmware version.
-
Input Source
: Shows the current input source and its resolution.