BenQ W1060 W1060 user manual - Page 43

Personalizing the projector menu display, Shutting down the projector

Get BenQ W1060 PDF manuals and user guides View all BenQ W1060 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

English Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. • Menu display time in the SYSTEM SETUP: Basic > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame. • Menu position in the SYSTEM SETUP: Basic > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position. • Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to select your language. • Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen. Shutting down the projector 1. To turn the projector off, press POWER OFF on the remote control to turn the projector off directly. Or you can press POWER on the projector and a warning message appears. Press POWER again. 2. Once the cooling process finishes, the POWER indicator light is a steady orange and fans stop. 3. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time. • To protect the lamp, the projector will not respond to any commands during the cooling process. • If the projector is not properly shut down, to protect the lamp, when you attempt to restart the projector, the fans will run for a few minutes to cool down. Press POWER again to start the projector after the fans stop and the POWER indicator light turns orange. • Lamp life results will vary depending on environmental conditions, and usage. Operation 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Operation
43
English
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
Menu display time
in the
SYSTEM SETUP: Basic
>
Menu Settings
menu sets the length
of time the OSD will remain active after your last key press. The time length ranges from
5 to 30 seconds in 5-second increments. Use
/
to select a suitable time frame.
•
Menu position
in the
SYSTEM SETUP: Basic
>
Menu Settings
menu sets the OSD
position in five locations. Use
/
to select a preferred position.
•
Language
in the
SYSTEM SETUP: Basic
menu sets your familiar language for the OSD
menus. Use
/
to select your language.
•
Splash Screen
in the
SYSTEM SETUP: Basic
menu sets a preferred logo screen to be
displayed during projector start-up. Use
/
to select a screen.
Shutting down the projector
1.
To turn the projector off, press POWER
OFF on the remote control to turn the
projector off directly. Or you can press
POWER
on the projector and a
warning message appears. Press
POWER
again.
2.
Once the cooling process finishes, the
POWER indicator light
is a steady
orange and fans stop.
3.
Disconnect the power cord from the wall
socket if the projector will not be used in
an extended period of time.
•
To protect the lamp, the projector will not
respond to any commands during the
cooling process.
•
If the projector is not properly shut down,
to protect the lamp, when you attempt to re-
start the projector, the fans will run for a few minutes to cool down. Press POWER again to
start the projector after the fans stop and the POWER indicator light turns orange.
•
Lamp life results will vary depending on environmental conditions, and usage.