BenQ W9000 User Manual - Page 19

Using the projector, Preparations, Selecting an input video source, Adjusting the projected image

Get BenQ W9000 - DLP Projector - HD 1080p PDF manuals and user guides
UPC - 840046018023
View all BenQ W9000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

English Using the projector Preparations 1. Plug in and turn all of the connected equipment on. 2. If not already in, plug the supplied power cable into the AC inlet on the rear of the projector and turn on the power switch. 3. Plug the power cable into a wall socket and turn the wall switch on. Turning the projector on Follow the steps below. 1. Make sure the Power light is orange after power has been applied and the main AC power switch is turned on. 2. Press and hold the POWER button on the projector or remote control to turn the projector on. The projector will not respond to further commands while it is warming up. 3. The fans will be start operating, and a start-up image displays on the screen for a few seconds while it warms up. 4. "Searching...." will be displayed on the screen before the projector identifies the input signal. This message will remain on the screen until a valid signal is detected. 5. If the horizontal frequency of the input signal exceeds the range of the projector, the message "Unsupported timing" will be displayed on the screen. This message will remain on-screen until you change the input signal to an appropriate source. Selecting an input video source The projector can be connected to multiple equipment at the same time. To select an individual input signal, press one of the Source buttons on the remote control, or to sequentially cycle through all possible sources, press the SOURCE/ ENTER button on the projector. • When the projector is first turned on, it will attempt to reconnect with the input source which was in use when the projector was last shut down. • If you want to use the PIP or POP function. See page 22 for details. Adjusting the projected image Adjusting the projection angle There are four adjuster feet on the bottom of the projector. These can be used if necessary to change the projection angle. Screw the feet in or out as appropriate to aim and level the projection angle. If the screen and the projector are not perpendicular to each other, the projected image becomes vertical trapezoidal. To correct this problem, you can adjust the value of Keystone in the Setup menu. Using the projector 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
19
Using the projector
English
Using the projector
Preparations
1.
Plug in and turn all of the connected equipment on.
2.
If not already in, plug the supplied power cable into the AC inlet on the
rear of the projector and turn on the power switch.
3.
Plug the power cable into a wall socket and turn the wall switch on.
Turning the projector on
Follow the steps below.
1.
Make sure the Power light is orange after power has been applied and the
main AC power switch is turned on.
2.
Press and hold the
POWER
button on the projector or remote control to
turn the projector on.
The projector will not respond to further commands while it is warming up.
3.
The fans will be start operating, and a start-up image displays on the screen
for a few seconds while it warms up.
4.
"Searching…." will be displayed on the screen before the projector identifies
the input signal. This message will remain on the screen until a valid signal is detected.
5.
If the horizontal frequency of the input signal exceeds the range of the projector, the message "Unsupported
timing" will be displayed on the screen. This message will remain on-screen until you change the input signal
to an appropriate source.
Selecting an input video source
The projector can be connected to multiple equipment at the same time. To
select an individual input signal, press one of the Source buttons on the remote
control, or to sequentially cycle through all possible sources, press the
SOURCE/
ENTER
button on the projector.
•
When the projector is first turned on, it will attempt to reconnect with the
input source which was in use when the projector was last shut down.
•
If you want to use the PIP or POP function.
See page 22
for details.
Adjusting the projected image
Adjusting the projection angle
There are four adjuster feet on the bottom of the projector. These can
be used if necessary to change the projection angle. Screw the feet in or
out as appropriate to aim and level the projection angle.
If the screen and the projector are not perpendicular to each other,
the projected image becomes vertical trapezoidal. To correct this
problem, you can adjust the value of Keystone in the Setup menu.