Binatone Boomerang User Guide - Page 22

Set the First Ring for Additional Handsets Only

Get Binatone Boomerang PDF manuals and user guides View all Binatone Boomerang manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

13.10 Change the Master PIN The Master PIN is used for registration/deregistration of handsets and for accessing the answering machine remotely. The default Master PIN number is 0000. The maximum length of the Master PIN is 8 digits. Note: If you forget your PIN code, you can reset it to its default 0000 using a handset Reset. • From the home screen, press . • Press to "SETTINGS" and then press to select. • Press to select "CHANGE PIN". • Enter the current Master PIN and then press to confirm. >>The PIN will be shown as asterisks (*) on the screen as you enter them. • Enter the new PIN and then press to confirm. >>A confirmation tone is played. • Press to return to the home screen. 13.11 Set the First Ring (for Additional Handsets Only) If you have subscribed to Caller Line Identification service and do not wish to hear the phone ring before the caller identification is displayed, you can set the "FIRST RING" to "OFF". • From the home screen of your additional handset, press . • Press to "ADVANCED SET" and then press to select. • Press to "FIRST RING" and then press to select. • Press to select "ON" or "OFF" and then press to confirm. >>A confirmation tone is played. • Press to return to standby mode. 13.12 Change the Recall Time You may need to press to send a Flash signal (also called Recall or Timed Break Recall) if you are connected to a PBX or using certain network services. You should normally leave the Recall Time at its default setting, Short (100ms). However, it can be changed to Medium (270ms) or Long (600ms) if your telephone is connected to a PBX that requires a different recall time. • From the home screen, press . • Press to "SETTINGS" and then press to select. • Press to "RECALL TIME" and then press to select. • Press to select "SHORT", "MEDIUM" or "LONG" and then press >>A confirmation tone is played. • Press to return to standby mode. to confirm. 13.13 Reset the Unit You can reset your phone to its default settings with this feature. Note: Upon reset, all your personal settings, call log and redial list entries will be deleted and the phone will return to its default settings, including the Master PIN. However, your phonebook will remain unchanged after reset and any recorded messages will remain unchanged, while all other settings will be reset. • From the home screen, press . • Press to "SETTINGS" and then press to select. • Press to select "RESET" and then press to select. • Press again to confirm. >>A confirmation tone is played and the unit is reset to its default settings.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
13.10
Change the Master PIN
The Master PIN is used for registration/deregistration of handsets and for accessing the answering machine
remotely. The default Master PIN number is 0000. The maximum length of the Master PIN is 8 digits.
Note:
If you forget your PIN code, you can reset it to its default 0000 using a handset Reset.
•
From the home screen, press
.
•
Press
to
“SETTINGS”
and then press
to select.
•
Press
to select
“CHANGE PIN”
.
•
Enter the current Master PIN and then press
to confirm.
> The PIN will be shown as asterisks (*) on the screen as you enter them.
•
Enter the new PIN and then press
to confirm.
> A confirmation tone is played.
•
Press
to return to the home screen.
13.11
Set the First Ring (for Additional Handsets Only)
If you have subscribed to Caller Line Identification service and do not wish to hear the phone ring before
the caller identification is displayed, you can set the
“FIRST RING”
to
“OFF”
.
•
From the home screen of your additional handset, press
.
•
Press
to
“ADVANCED SET”
and then press
to select.
•
Press
to
“FIRST RING”
and then press
to select.
•
Press
to select
“ON”
or
“OFF”
and then press
to confirm.
> A confirmation tone is played.
•
Press
to return to standby mode.
13.12
Change the Recall Time
You may need to press
to send a Flash signal (also called Recall or Timed Break Recall) if you are
connected to a PBX or using certain network services. You should normally leave the Recall Time at its
default setting, Short (100ms). However, it can be changed to Medium (270ms) or Long (600ms) if your
telephone is connected to a PBX that requires a different recall time.
•
From the home screen, press
.
•
Press
to
“SETTINGS”
and then press
to select.
•
Press
to
“RECALL TIME”
and then press
to select.
•
Press
to select
“SHORT”
,
“MEDIUM”
or
“LONG”
and then press
to confirm.
> A confirmation tone is played.
•
Press
to return to standby mode.
13.13 Reset the Unit
You can reset your phone to its default settings with this feature.
Note:
Upon reset, all your personal settings, call log and redial list entries will be deleted and the phone will
return to its default settings, including the Master PIN. However, your phonebook will remain unchanged
after reset and any recorded messages will remain unchanged, while all other settings will be reset.
•
From the home screen, press
.
•
Press
to
“SETTINGS”
and then press
to select.
•
Press
to select
“RESET”
and then press
to select.
•
Press
again to confirm.
> A confirmation tone is played and the unit is reset to its default settings.