Biostar M7VIG PRO D M7VIG Pro D BIOS setup guide - Page 25

Modem Use IRQ, Soft-Off by PWRBTN, State After power failure, Wake Up/ Power On Control, Power On - motherboard manual

Get Biostar M7VIG PRO D PDF manuals and user guides View all Biostar M7VIG PRO D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

M7VIG Pro-D BIOS Setup Initial display power management signaling. Modem Use IRQ This determines the IRQ, which can be applied in MODEM use. The Choices: 3 (default),4 / 5 / 7 / 9 / 10 / 11 / NA. Soft-Off by PWRBTN Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state when the system has "hung." The Choices: Delay 4 Sec, Instant-Off (default). State After power failure This field determines the action the system will automatically take when power is restored to a system that had lost power previously without any subsequent manual intervention. There are 3 sources that provide current to the CMOS area that retains these Power-On instructions; the motherboard battery (3V), the Power Supply (5VSB), and the Power Supply (3.3V). While AC is not supplying power, the motherboard uses the motherboard battery (3V). If AC power is supplied and the Power Supply is not turned on, 5VSB from the Power Supply is used. When the Power Supply is eventually turned on 3.3V from the Power Supply will be used. There are 3 options: "Former-Sts", "On", "Off". "Former-Sts" "On" "Off" (default) Means to maintain the last status of the CMOS when AC power is lost. Means always set CMOS to the "On" status when AC power is lost Means always set CMOS to the "Off" status when AC power is lost. For example: If set to "Former-Sts" and AC power is lost when system is live, then after AC power is restored, the system will automatically power on. If AC power is lost when system is not live, system will remain powered off. Wake Up/ Power On Control If you highlight the literal "Press Enter" next to the "Wake Up/ Power On Control" label and then press enter key, it will take you to a submenu with the following options: Power On by PCI card When you select Enabled, a PME signal from PCI card returns the system to Full On state. The Choices: Disabled (default), Enabled. Wake Up on LAN/Ring An input signal on the serial Ring Indicator (RI) line (in other words, an 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
M7VIG Pro-D BIOS Setup
24
Initial display power management signaling.
Modem Use IRQ
This determines the IRQ, which can be applied in MODEM use.
The Choices: 3
(default),4 / 5 / 7 / 9 / 10 / 11 / NA.
Soft-Off by PWRBTN
Pressing the power button for more than 4 seconds forces the system to enter the
Soft-Off state when the system has “hung.”
The Choices:
Delay 4 Sec,
Instant-Off
(default).
State After power failure
This field determines the action the system will automatically take when power is restored
to a system that had lost power previously without any subsequent manual intervention.
There are 3 sources that provide current to the CMOS area that retains these Power-On
instructions; the motherboard battery (3V), the Power Supply (5VSB), and the Power
Supply (3.3V). While AC is not supplying power, the motherboard uses the motherboard
battery (3V). If AC power is supplied and the Power Supply is not turned on, 5VSB from
the Power Supply is used. When the Power Supply is eventually turned on 3.3V from the
Power Supply will be used.
There are 3 options: “Former-Sts”, “On”, “Off”.
“Former-Sts”
Means to maintain the last status of the CMOS when AC
power is lost.
“On”
Means always set CMOS to the “On” status when AC
power is lost
“Off”
(default)
Means always set CMOS to the “Off” status when AC
power is lost.
For example: If set to “Former-Sts” and AC power is lost when system is live, then after
AC power is restored, the system will automatically power on. If AC power is lost when
system is not live, system will remain powered off.
Wake Up/ Power On Control
If you highlight the literal “Press Enter” next to the “Wake Up/ Power On Control” label
and then press enter key, it will take you to a submenu with the following options:
Power On by PCI card
When you select Enabled, a PME signal from PCI card returns the system to
Full On state.
The Choices: Disabled
(default), Enabled.
Wake Up on LAN/Ring
An input signal on the serial Ring Indicator (RI) line (in other words, an