Bissell PowerEdge Lift-Off Steam Mop Hard Surface Steam Cleaner 20781 User Gui - Page 7

Page 7 highlights

Cleaning Your Hard Floors NOTE: Before you clean, thoroughly sweep or vacuum floor prior to cleaning with your PowerEdge™ Lift-Off® Steam Mop. Your hard floor cleaner is designed to clean hard flooring, such as ceramic tile, marble, stone and sealed hard wood floors. Use on waxed or some unwaxed floors may result in a diminished glossiness. The hard floor cleaner is not for use on unsealed wood floors. For best results, test in an inconspicuous area and check the care instructions from your flooring manufacturer. 1 2 Attach mop pad by wrapping around bottom of foot, making sure gray stitching is located on the front of foot and the Quick Grip Release Tab is located on the back. Plug machine into an outlet. 3 4 5 When the machine is plugged in, the READY light will start to blink. The READY light will turn to a solid light when the machine is ready to use. Step on the back of the foot to recline the body of machine to begin cleaning. Push the trigger on the handle to release steam. 6 To be sure to sanitize an 7 For optimum area of your floor, use the microfiber cloth pad x2 corner cleaning, perform two and slowly and evenly cleaning strokes stroke your steam mop along each wall back and forth at least towards the corner three times over the to be cleaned. area using continuous steam. For best results, When done remove the pad and wash after use. x2 cleaning, unplug the machine. NOTE: Upon the first use of your steam mop or first use after refilling the water tank, the pump may make a "knocking" sound. This is normal and will diminish after a few seconds. NOTE: The steam mop generates hot steam, so move the unit continuously when depressing the trigger as damage to flooring can occur. The trigger does not need to be depressed at all times. www.BISSELL.com 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
www.BISSELL.com
7
x2
x2
Cleaning Your Hard Floors
When the machine is
plugged in, the READY
light will start to blink.
The READY light will turn
to a solid light when the
machine is ready to use.
Plug machine into an outlet.
Push the trigger on the
handle to release steam.
1
2
Attach mop pad by
wrapping around bottom
of foot, making sure gray
stitching is located on
the front of foot and the
Quick Grip Release Tab is
located on the back.
Step on the back of the
foot to recline the body of
machine to begin cleaning.
5
For optimum
corner cleaning,
perform two
cleaning strokes
along each wall
towards the corner
to be cleaned.
When done
cleaning, unplug
the machine.
To be sure to sanitize an
area of your floor, use
the microfiber cloth pad
and slowly and evenly
stroke your steam mop
back and forth at least
three times over the
area using continuous
steam. For best results,
remove the pad and
wash after use.
7
6
4
NOTE:
Before you clean, thoroughly sweep or vacuum floor prior to cleaning
with your PowerEdge™ Lift-Off® Steam Mop. Your hard floor cleaner is
designed to clean hard flooring, such as ceramic tile, marble, stone and sealed
hard wood floors. Use on waxed or some unwaxed floors may result in a
diminished glossiness. The hard floor cleaner is not for use on unsealed wood
floors. For best results, test in
an inconspicuous area and check the care
instructions from your flooring manufacturer.
3
NOTE:
Upon the first use of your steam mop or first use after refilling the
water tank, the pump may make a “knocking” sound. This is normal and will
diminish after a few seconds.
NOTE:
The steam mop generates hot steam, so move the unit continuously
when depressing the trigger as damage to flooring can occur. The trigger
does not need to be depressed at all times.