Black & Decker CM1936 Type 2 Manual - CM1936 - Page 6

AA1 BA2 - blade

Get Black & Decker CM1936 PDF manuals and user guides View all Black & Decker CM1936 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Preparation Please refer to diagrams (A, B, C...) AND ITEM NUMBERS (1, 2, 3...) AS NOTED THROUGHOUT MANUAL. For example, A-1 refers to Item 1 in Figure A. Unpacking - (FigureS A, A1, A2) Step 1: Raise the handle section A-1 into place and secure by tightening the two lower knobs A-2. Be careful not to pinch power cord. CAUTION: Pinch point. To avoid being pinched, keep fingers away from area between handles when raising. A Step 2: Carefully cut down the sides of the box on the opposite end of the handle and fold the flap down as shown. WARNING: Sharp blade. Keep body parts away from blade. A1 Step 3: With the carton end cut open, remove the cardboard filler, charger, accessory bag and grass bag and push the mower out of the opened carton. A2 HANDLE ADJUSTMENT - (Figure B) Your mower has a variable height handle adjustment feature. To adjust the handle position to suit your height preference, use the following procedure: 1. Remove both hex nuts and flat washer B-1 on the middle part of the handlebars using a 1/2 inch wrench. Remove the carriage bolts B-2. 2. Slide the upper handle into one of the 3 adjustment positions B-3, aligning the holes in the upper and lower handles. 3. Insert carriage bolts and install the flat washers and hex nuts, tighten securely. B 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
6
PREPARATION
PLEASE REFER TO DIAGRAMS (A, B, C...) AND ITEM NUMBERS (1, 2, 3...) AS NOTED THROUGHOUT MANUAL. FOR EXAMPLE,
A-1 REFERS TO ITEM 1 IN FIGURE A.
UNPACKING -
(FIGURES A, A1, A2)
STEP 1:
Raise the
handle section
A-1
into place and secure by tightening the two
lower knobs
A-2
. Be careful not to pinch power cord.
CAUTION:
Pinch point.
To avoid being pinched, keep fingers away
from area between handles when raising.
STEP 2:
Carefully cut down the sides of the box on the opposite end of the handle
and fold the flap down as shown.
WARNING:
Sharp blade.
Keep
body parts away from blade.
STEP 3:
With the carton end cut open, remove the cardboard filler, charger,
accessory bag and grass bag and push the mower out of the opened
carton.
HANDLE ADJUSTMENT -
(FIGURE B)
Your mower has a variable height handle adjustment feature. To adjust the
handle position to suit your height preference, use the following procedure:
1. Remove both
hex nuts and flat washer
B-1
on the middle part of the
handlebars using a 1/2 inch wrench. Remove the
carriage bolts B-2
.
2. Slide the upper handle into one of the 3 adjustment positions
B-3
,
aligning the holes in the upper and lower handles.
3. Insert carriage bolts and install the flat washers and hex nuts, tighten
securely.
6
A
B
A1
A2