Black & Decker IR1350S User Manual - Page 1
Black & Decker IR1350S Manual
View all Black & Decker IR1350S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Size: 19.685" x 17.5" Please Read and Save this Use and Care Book. IMPORTANT SAFETY INSTRUCTIONS When using your iron, basic safety precautions should always be followed, including the following: ❍ READ ALL INSTRUCTIONS BEFORE USING. ❍ Use iron only for its intended use. ❍ To protect against a risk of electric shock, do not immerse the iron in water or other liquids. ❍ The iron should always be turned to the minimum (min) setting before plugging or unplugging from outlet. Never yank cord to disconnect from the outlet; instead grasp plug and pull to disconnect. ❍ Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing. ❍ Always disconnect iron from electrical outlet when filling with water or emptying, and when not in use. ❍ Do not operate iron with a damaged cord, or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron; take it to a qualified service person for examination and repair, or call the appropriate toll-free number on the cover of this manual. Incorrect reassembly can cause a risk of electric shock when the iron is used. ❍ Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board. ❍ Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down or use the surge of steam-there may be hot water in the reservoir. Avoid rapid movement of iron to minimize hot water spillage. ❍ The iron must be used and rested on a stable surface. - When placing the iron on its stand, ensure that the surface on which the stand is placed is stable. - The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking. SPECIAL INSTRUCTIONS ❍ To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit. ❍ If an extension cord is absolutely necessary, a 15-ampere and 120-volt should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. ❍ This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. ❍ Children should be supervised to ensure that they do not play with the appliance. SAVE THESE INSTRUCTIONS. This product is for household use only. POLARIZED PLUG This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way. TAMPER-RESISTANT SCREW Warning: This appliance is equipped with a tamper-resistant screw to prevent removal of the outer cover. To reduce the risk of fire or electric shock, do not attempt to remove the outer cover. There are no user-serviceable parts inside. Repair should be done only by authorized service personnel. Note: If the power supply cord is damaged, it should be replaced by qualified personnel or in Latin America by an authorized service center. 1. Spray nozzle 2. Water-fill cover 3. Variable steam selector 4. Steam button 5. Spray button 6. Power indicator light 7. Comfort GripTM handle 8. 360° pivoting cord 9. Heel rest 10. Fabric-select dial 11. Water tank 12. Auto Clean® button 13. Soleplate How to Use This product is for household use only. GETTING STARTED • Remove any labels, stickers or tags attached to the body or soleplate of the iron. • Please go to www.prodprotect.com/applica to register your warranty. Note: Use ordinary tap water for ironing. Do not use water processed through a home softening system. Important: For optimum performance, let the iron stand for 90 seconds before beginning to iron. Tip: If unsure of a garment's fiber, test a small area (on an inside seam or hem) before ironing. FILLING WATER TANK 1. With iron on a flat surface with soleplate down or tilted at a 45-degree angle, open the water-fill cover. 2. Using a clean measuring cup, pour water into opening until water reaches the MAX level mark on the side of the water tank. Do not overfill. AUTOMATIC SHUTOFF IN 3 POSITIONS 1. The iron will automatically turn to stand by mode after 30 seconds of inactivity if left on its soleplate or on its side. If left vertically on its heel rest, it will turn off after 8 minutes. 2. The red power indicator light starts blinking to let you know the iron has stopped heating. Important: The iron will have turned off but will still be hot. 3. Once the iron is picked up, an internal motion sensor is activated and the iron starts heating again. 4. Allow iron to reheat completely before resuming ironing. SELECTING FABRIC SETTING 1. Read fabric labels to help determine fabric type to be ironed. 2. Once you determine the fabric type, turn the fabric-select dial to select the appropriate fabric setting. Important: Always stand the iron on its heel when powered on but not in use. USING VARIABLE STEAM Note: Be sure the water tank is filled. 1. This iron produces steam at settings 4 through 6. Turn the fabric-select dial to the appropriate setting for your fabric. 2. Push the variable steam selector to desired amount of steam. The higher the setting selected, the more powerful the steam. Note: For no steam, the variable steam selector should be set to the . STEAM BUTTON Note: Be sure the water tank is filled. 1. With the water tank filled to the MAX mark, turn the fabric select dial to appropriate setting (between 4 and 6) and let iron stand on its heel rest about 90 seconds. 2. Press the steam button to generate a burst of steam. For best performance, leave an interval of 5 seconds between bursts. Note: On first use, pump the steam button several times. Product may vary slightly from what is illustrated. HORIZONTAL STEAM IRONING 1. Fill water reservoir to MAX line. 2. Turn the fabric select dial to select desired setting. 3. Set the variable steam selector to desired amount of steam. 4. When finished ironing, turn the fabric-select dial to the lowest setting. Make sure the variable steam selector is set to dry and unplug the iron. 5. Stand the iron on its heel rest and allow it to cool off. VERTICAL STEAMING Use to remove wrinkles or creases from hanging garments or drapes. 1. Turn the fabric-select dial to select desired setting for the fabric to be ironed. 2. Hold iron close to, but not touching fabric. 3. Pull fabric taut with your free hand and press the steam button as you move the iron over the fabric. Important: Do not bring iron too close to hand holding fabric to avoid heat. 4. For best performance, leave an interval of 5 seconds between bursts. SPRAY BUTTON Note: Be sure the water tank is filled. 1. Press the spray button to generate a spray of water. Note: On first use, pump the spray button several times. Important: Do not spray silk. DRY IRONING 1. Set the variable steam selector to . 2. Turn the fabric-select dial to appropriate setting for your fabric. 3. When finished ironing, make sure to unplug the iron. Important: Always stand the iron on its heel rest when powered on or not in use. Care and Cleaning This product contains no user serviceable parts. Refer service to qualified service personnel. CLEANING 1. Make sure iron is unplugged and has cooled completely. Wipe the soleplate and outer surfaces with a soft cloth dampened with water and mild household detergent. Never use abrasives, heavy-duty cleansers, vinegar or scouring pads that may scratch or discolor the iron. 2. After cleaning, steam iron over an old cloth to remove any residue from the steam vents. AUTO CLEANTM SYSTEM To keep the steam vents free of any buildup, follow these instructions about once a month. 1. Fill the water tank well below MAX line. Plug in the iron. 2. Select fabric setting 6 on the fabric-select dial and stand the iron on its heel rest. 3. Wait 2 minutes for the iron to heat fully, then unplug the iron. 4. Hold iron over a sink with the soleplate facing down. 5. Press the Auto CleanTM button. Important: Be careful, as after several seconds, hot water and steam will come out of the steam vents. 6. Continue to hold Auto CleanTM button until all the water has emptied. If necessary, move iron side-to-side and front-to-back. 7. When finished, release the button, stand the iron on its heel rest and plug it in. Heat for about 2 minutes to dry out any remaining water. STORING YOUR IRON 1. Unplug the iron and let it cool completely. 2. Check that the fabric-select dial is set to . 3. Store iron on its heel rest. Comercializado por: Importado por / Imported by: Rayovac de México S.A de C.V Autopista México Querétaro No 3069-C Oficina 004 RAYOVAC ARGENTINA S.R.L. Humboldt 2495 Piso #3 (C1425FUG) C.A.B.A. Argentina. C.U.I.T NO. 30-70706168-1 Colonia San Andrés Atenco, Tlalnepantla Estado de México, C.P. 54040 Mexico. Telefono: (55) 5831 - 7070 Para atención de garantía marque: 01 800 714 2503 Importado por / Imported by: Rayovac de México S.A de C.V Autopista México Querétaro No 3069-C Oficina 004 Colonia San Andrés Atenco, Tlalnepantla Estado de México, C.P. 54040 Servicio y Reparación Art. 123 No. 95 Col. Centro, C.P. 06050 Deleg. Cuauhtemoc Mexico. Telefono: (55) 5831 - 7070 Para atención de garantía marque: 01 800 714 2503 Servicio al Consumidor, Venta de Refacciones y Accesorios 01 800 714 2503 Por favor llame al número correspondiente que aparece en la lista a continuación para solicitar que se haga efectiva la garantía y donde Ud. puede solicitar servicio, reparaciones o partes en el país donde el producto fué comprado. Argentina Servicio Técnico Monroe 3351 CABA Argentina Tel: 0800 - 444 - 7296 [email protected] Nicaragua ServiTotal De semáforo de portezuelo 500 metros al sur. Managua, Nicaragua, Tel. (505) 248-7001 Argentina SERVICIO DE MAQUINAS Y HERRAMIENTAS LTDA. Portugal Nº 644 Santiago - Chile Fonos: 02-6355208 / 02-6341169 Email: [email protected] Call center: 800-171-051 Colombia Rayovac Varta S.A Carrera 17 Número 89-40 Línea gratuita nacional Tel. 018000510012 Costa Rica Aplicaciones Electromecanicas, S.A. Calle 26 Bis y Ave. 3 San Jose, Costa Rica Tel. (506) 257-5716 / 223-0136 [email protected] Ecuador SERVICIO MASTER ECUADOR ALMERIA N50-71 Y DE LOS ALAMOS Tel. (593) 2281-3882 / 2240-9870 El Salvador Calle San Antonio Abad 2936 San Salvador, El Salvador Tel. (503) 2284-8374 Guatemala MacPartes SA 3ª Calle 414 Zona 9 Frente a Tecun Tel. (502) 2331-5020 / 2332-2101 Panamá Servicios Técnicos CAPRI Tumbamuerto Boulevard El Dorado Panamá 500 metros al sur. Tel. 3020-480-800 sin costo (507) 2360-236 / 159 Panamá Servicio Central Fast Service Av. Angamos Este 2431 San Borja, Lima Perú Tel. (511) 2251 388 Puerto Rico Buckeye Service Jesús P. Piñero #1013 Puerto Nuevo, SJ PR 00920 Tel.: (787) 782-6175 Republica Dominicana Prolongación Av. Rómulo Betancourt Zona Industrial de Herrera Santo Domingo, República Dominicana Tel.: (809) 530-5409 Venezuela Inversiones BDR CA Av. Casanova C.C. City Market Nivel Plaza Local 153 Diagonal Hotel Melia, Caracas. Tel. (582) 324-0969 www.applicaservice.com [email protected] Honduras ServiTotal Contigua a Telecentro Tegucigalpa, Honduras, Tel. (504) 235-6271 Código de fecha / Date Code / Le code de date: México Articulo 123 # 95 Local 109 y 112 Col. Centro, Cuauhtemoc, México, D.F. Tel. 01 800 714 2503 BLACK+DECKER and the BLACK+DECKER logo are trademarks of The Black & Decker Corporation and are used under license. All rights reserved Sello del Distribuidor: Fecha de compra: Modelo: BLACK+DECKER y el logo tipo BLACK+DECKER son marcas registradas de T he Black & Decker Corporation y son utilizados bajo licencia. Todos los derechos reservados. 320 W 120V~ 60 Hz © 2014 The Black & Decker Corporation and Spectrum Brands, Inc. Middleton, WI 53562 T22-5001304 10892-00 E/S Made and Printed in People's Republic of China Fabricado e Impreso en la República Popular de China PROFESSIONAL STEAM IRON PLANCHA DE VAPOR PROFESIONAL Customer Care Line: USA 1-800-231-9786 Accessories/Parts (USA) 1-800-738-0245 For online customer service and to register your product, go to www.prodprotect.com/applica Servicio para el cliente: México 01-800 714-2503 Accesorios/Partes (EE.UU) 1-800-738-0245 Para servicio al cliente y para registrar su garantía, visite www.prodprotect.com/applica When using your iron for the first time, you may notice water residue inside the unit. This is normal. Cuando use su plancha por primera vez, notará que hay agua adentro de la plancha. Esto es normal. MODEL/MODELO ❍ IR1350S