Black & Decker PPRH5B Instruction Manual - Page 5
Jump-starter, Volt Ac, Portable, Power, Supply, Volt Dc Portable Power Supply - instruction manual
View all Black & Decker PPRH5B manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
Jump-Starter This Jump-Starter is equipped with an On/Off Power Switch. Once the connections are properly made, turn the switch on to jump-start the vehicle. 1. T urn off vehicle ignition and all accessories (radio, A/C, lights, connected cell phone chargers, etc.). Place vehicle in "park" and set the emergency brake. 2. Make sure the Jump-Starter Power Switch is turned to off. 3. Remove jumper clamps from clamp tabs. Connect the red clamp first, then the black clamp. 4.Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative battery terminal is connected to chassis) (MOST COMMON) 4a. Connect positive (+) red clamp to vehicle battery's positive terminal. 4b. C onnect negative (-) black clamp to chassis or a solid, non-moving, metal vehicle component or body part. Never clamp directly to negative battery terminal or moving part. Refer to the automobile owner's manual. 5.Procedure for jump-starting POSITIVE GROUND SYSTEMS Notes: In the rare event that the vehicle to be started has a Positive Grounded System (positive battery terminal is connected to chassis), replace steps 4a and 4b above with steps 5a and 5b, then proceed to step 6. 5a. Connect negative (-) black clamp to vehicle battery's negative terminal. 5b. C onnect positive (+) red clamp to vehicle chassis or a solid, non-moving, metal vehicle component or body part. Never clamp directly to Positive battery terminal or moving part. Refer to the automobile owner's manual. 6. When clamps are connected properly, turn the Jump-Starter Power Switch to ON. 7. Turn ON the ignition and crank the engine in 5-6 second bursts until engine starts. 8. Turn the Jump-Starter Power Switch back to the OFF position. 9. Disconnect the negative (-) engine or chassis clamp first, then disconnect the positive (+) battery clamp. WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: • FOLLOW ALL SAFETY INSTRUCTIONS FOUND IN THE "Specific safety instructions for jump starters" section of this instruction manual. • This power system is to be used ONLY on vehicles with 12‑volt DC battery systems. • Never touch red and black clamps together - this can cause dangerous sparks, power arcing, and/ or explosion. • Always turn the unit off when not in use. CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE: • Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump- started. Before jump-starting this type of vehicle, read the vehicle manual to confirm that externalstarting assistance is advised. • Excessive engine cranking can damage the vehicle's starter motor. If the engine fails to start after the recommended number of attempts, discontinue jump-start procedure and look for other problems that need to be corrected. • If the connections to the battery's positive and negative terminals are incorrect, the reverse polarity indicator will light and the unit will sound a continuous alarm until the clamps are disconnected. Disconnect clamps and reconnect to battery with correct polarity. • If vehicle fails to start, turn off the ignition, turn off the jump-starter power switch, disconnect the jump-start system's leads and contact a qualified technician to investigate why the engine did not start. • Recharge this unit fully after each use. 120 volt AC portable power supply Rated Versus Actual Current Draw of Equipment Most electrical tools, appliances, electronic devices and audio/visual equipment have labels that indicate the power consumption in amps or watts. Be sure that the power consumption of the item to be operated is below 500 watts. If the power consumption is rated in amps AC, simply multiply by the AC volts (120) to determine the wattage. Resistive loads are the easiest for this unit to run; however, it will not run larger resistive loads (such as electric stoves and heaters), which require far more wattage than the unit can deliver on a continuous basis. Inductive loads (such as TVs and stereos) require more current to operate than do resistive loads of the same wattage rating. CAUTION: Rechargeable Devices • Certain rechargeable devices are designed to be charged by plugging them directly into an AC receptacle. These devices may damage the inverter or the charging circuit. • When using a rechargeable device, monitor its temperature for the initial ten minutes of use to determine if it produces excessive heat. • If excessive heat is produced, this indicates the device should not be used with this inverter. • This problem does not occur with most of the battery-operated equipment. Most of these devices use a separate charger or transformer that is plugged into an AC receptacle. • The inverter is capable of running most chargers and transformers. Power Inverter Output Waveform The AC output waveform of this inverter is known as a modified sine wave. It is a stepped waveform that has characteristics similar to the sine wave shape of utility power. This type of waveform is suitable for most AC loads, including linear and switching power supplies used in electronic equipment, transformers, and small motors. Using the Dual 120 Volt AC Outlets The two 120 volt AC outlets each are located under a protective cover on the left hand side of the front panel (refer to the Features section to locate). The two outlets support a combined maximum power draw of 500 watts. 1. Press the inverter power switch to turn the inverter on (I). The inverter power indicator will light red to indicate the two 120 volt AC outlets are ready to use. 2. Lift up the cover of the120 volt AC outlet. 3. Insert the 120 volt AC plug from the appliance into the 120 volt AC outlet. 4. Switch on the appliance and operate as usual. 5. Periodically check the unit's battery status by pressing the battery power level button. (Two red and one green battery status indicator lights indicate a full battery. Only one red battery status indicator lights indicates that the unit needs to be recharged.) Protective Features The inverter monitors the following conditions: Low internal battery voltage: The inverter will automatically shut down when the battery voltage drops too low, as this can harm the battery. High internal battery voltage: The inverter will automatically shut down when the battery voltage is too high, as this can harm the unit. Thermal shutdown protection: The inverter will automatically shut down when the unit becomes overheated. Overload/short circuit protection: The inverter will automatically shut down when an overload or short circuit occurs. Important Notes: The inverter power indicator will flash red to indicate that one of the above fault conditions is present before automatic shutdown occurs. Should this occur, take the following steps: 1. Disconnect all appliances from the unit. 2. Press the inverter power switch to turn the inverter off (O). 3. Allow the unit to cool down for several minutes. 4. Make sure the combined rating for all appliances plugged into the unit is 500 watts or lower and that appliance cord(s) and plug(s) are not damaged. 5. Assure there is adequate ventilation around the unit before proceeding. 12 volt DC portable power supply The 12 volt DC accessory outlet is located under a protective cover on the right hand side of the front panel (refer to the Features section to locate). This portable power source is for use with all 12 volt DC accessories equipped with a male accessory outlet plug that are rated up to 5 amps. 1. Lift up the cover of the unit 's 12 volt DC outlet. 2. Insert the 12 volt DC plug from the appliance into the 12 volt accessory outlet on the unit. DO NOT EXCEED A 5 AMP LOAD.