Bosch B10CB80NVB Instructions for Use - Page 6
Installing the appliance, Ventilation, Connecting the appliance
View all Bosch B10CB80NVB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
en-us Installing the appliance Have a technician install and connect the appliance according to the enclosed installation instructions. , WARNING: Do not install this appliance: ■ outdoors, ■ in an environment with dripping water, ■ in rooms where there is a risk of frost. Transporting The appliances are heavy and must be secured during transportation and installation. Because of the weight/dimensions of the appliance and to minimize the risk of injuries and damage to the appliance at least two persons are necessary to set-up the appliance securely. Installation location A dry, well ventilated room is suitable as an installation location. The installation location should not be exposed to direct sunlight and not placed near a heat source, e.g. a cooker, radiator, etc. If installation next to a heat source is unavoidable, use a suitable insulating plate or observe the following minimum distances from the heat source: ■ To electric or gas cookers 11/4" (3 cm). ■ To an oil or coal-fired cooker 1113/16" (30 cm). The floor of the installation location must not give way; if required, reinforce floor. Ventilation The air on the rear panel and on the side panels of the appliance heats up. Conduction of the heated air must not be obstructed. Otherwise the refrigeration unit must work harder. This increases power consumption. Therefore: Never cover or block ventilation openings! Connecting the appliance After installing the appliance, wait at least 1 hour until the appliance starts up. During transportation the oil in the compressor may have flowed into the refrigeration system. Before switching on the appliance for the first time, clean the interior of the appliance (see chapter "Cleaning the appliance"). Electrical connection , WARNING: Avoid the risk of an electric shock! , WARNING: Insert into a grounded 3-phase socket. Never remove grounding phase. Do not use any adapters. Do not use any extension cables. , WARNING: Non-compliance with these instructions may result in death, fire or an electric shock. Improper connection of the protective conductor may result in an electric shock. If you are in doubt whether the appliance has been grounded properly, have the appliance tested by a qualified electrician or service technician. Do not use extension cables or distributors. This appliance must be connected to a permanently installed socket. The socket must be near the appliance and also freely accessible following installation of the appliance. The appliance complies with protection class I. Connect the appliance to 115 V/60 Hz alternating current via a correctly installed socket with protective conductor. The socket must be fused with a 10 to 16 A fuse. The appliance comes with a UL registered 3-wire power cord. The appliance requires a 3-pole socket. Please observe the following table with regard to this: Appliance Fridge-freezer Maximum simultaneous load 6.0 amps Check on the rating plate whether the indicated voltage and current type correspond with the values of your power supply. The location of the rating plate can be found in the chapter entitled Customer service. , WARNING: Never connect the appliance to electronic energy saver plugs. Our appliances can be used with mains and sine-controlled inverters. Mains-controlled inverters are used for photovoltaic systems which are connected directly to the national grid. Sine-controlled inverters must be used for isolated applications (e.g. on ships or in mountain lodges) which are not connected directly to the national grid. 6
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54