Home » Bosch Manuals » Dishwashers » Bosch SGE68X55UC » Manual Viewer

Bosch SGE68X55UC Instruction manual - Page 33

Interrupting the wash cycle, Terminating the wash cycle, Reset, Changing the wash cycle, Child Lock

Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Interrupting the wash cycle 9 CAUTION Expansion (overpressure) may cause the appliance door to open and/or water to escape! If the door was opened on an appliance which has a hot water connection or is heated, always leave the door ajar for several minutes and then close. 1. Press On/Off button (. The LED's go out. The wash cycle is saved. 2. To continue the wash cycle, close the door and press On/Off button ( again. Note: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 seconds after pressing the Start button, the operation will be paused. Close the appliance door and press the Start button P again. Terminating the wash cycle (Reset) 1. Press and hold Start button P Terminatingthewashcycle for approximately 3 seconds until the display reads ‹:‹,. 2. Wait about 1 minute while the dishwasher drains. 3. Press On/Off button (. You may now power the dishwasher back on and begin a new cycle if desired. Operating the Dishwasher en-us Changing the wash cycle When the Start button ( has been pressed, the wash cycle cannot be changed. The only way a wash cycle can be changed is by terminating the wash cycle (Reset). Child Lock (panel lock) The child lock will lock the panel while the dishwasher is in operation to prevent that a wash cycle is interrupted unintenionally (e.g. by children). To set the panel lock: 1. Start the desired wash cycle. 2. Hold down the button with the / symbol over it for approximately 3 seconds until the display reads '-. The panel lock is active. '- will be indicated now if any button is pressed and the program will not be reset. To deactivate the panel lock hold down the button with the / over it for approximately 3 seconds until the display no longer reads '-. The panel lock is deactivated automatically when the wash cycle is completed. In case of a power outage the panel lock will remain active. The panel lock has to be activated with each new wash cycle. 33

Section	Page
Table of contents	3
en-us Operating instructions	3
( Safety Definitions 5	3
( IMPORTANT SAFETY INSTRUCTIONS 6	3
ƒ Causes of Damage 9	3
* Getting Started 10	3
+ Water softening system / special salt 13	3
, Rinse Aid 14	3
- Loading the Dishwasher 16	3
. Detergent 25	3
/ Dishwasher Cycles 27	3
0 Dishwasher Cycle Options 28	3
1 Operating the Dishwasher 30	3
2 Care and Maintenance 34	3
3 Troubleshooting 39	3
4 Customer Service 48	3
‡ Statement of Limited Product Warranty 49	3
( Safety Definitions	5
Safety Definitions	5
9 WARNING	5
9 CAUTION	5
NOTICE	5
Note:	5
( IMPORTANT SAFETY INSTRUCTIONS	6
IMPORTANT SAFETY INSTRUCTIONS	6
READ AND SAVE THESE INSTRUCTIONS	6
To reduce the risk of fire, electrical shock, or serious injury, observe the following:	6
Risk of fire, electrical shock, or serious injury	6
9 WARNING	6
Risk of injury or death!	6
9 WARNING	6
Risk of injury!	6
9 WARNING	6
Risk of electrical shock or fire!	6
9 WARNING	6
Health hazard!	6
GROUNDING INSTRUCTIONS	7
9 WARNING	7
Risk of electric shock!	7
Safe Operation	7
9 CAUTION	7
9 WARNING	8
Risk of injury!	8
Child Safety	8
Proper Care and Maintenance	8
9 WARNING	8
Risk of explosion!	8
Note:	9
NOTICE	9
State of California Proposition 65 Warning:	9
9 WARNING	9
ƒ Causes of Damage	9
Causes of Damage	9
NOTICES	9
* Getting Started	10
Getting Started	10
Appliance overview	10
Operating panel	11
Note:	11
Dishwasher interior components	11
Display indicators	11
Menu overview	12
Setting	12
Factory setting	12
Description	12
+ Water softening system / special salt	13
Water softening system / special salt	13
Water hardness table	13
Adjusting the water softening system	13
Set the softening system as follows:	13
1. Ask your local water utility company for the water hardness value of your tap water or use test strip.	13
2. Required setting can be found in the water hardness table.	13
3. Press On/Off button (.	13
4. Hold down function key # and press Start button P until the display 8 indicates •:‹x (x can be any number).	13
5. Release both buttons. The indicator of function key # flashes and the display 8 indicates •:‹‹. Press function key 3 to select the desired setting.	13
6. Press Start button P to save the setting.	13
Using special dishwasher salt	14
NOTICE	14
Top off the salt as follows:	14
1. Undo the screw plug on the dispenser 1Z.	14
2. Fill the dispenser with water (required only when switching on the appliance for the first time).	14
3. Add salt as illustrated (do not use table salt, salt tablets or salt for use with whole house water softeners).	14
Using detergents with salt component	14
Detergent with a salt component	14
Switching off low salt indicator / water softening system	14
Switching off water softening system	14
, Rinse Aid	14
Rinse Aid	14
Note:	14
Adding rinse aid	15
NOTICE	15
1. Open the rinse aid dispenser 9* by pressing on the latch of the lid and pull it open.	15
2. Add liquid rinse aid to the dispenser 9* until it is full. Do not overfill. Avoid spilling into air vent hole.	15
3. Close the lid. Lid must be fully closed until it clicks in order to seal.	15
4. Wipe up any excess rinse aid that may have puddled when the dispenser reservoir is full.	15
Tip:	15
NOTICE	15
Setting the amount of rinse aid used	15
Setting	15
Amount	15
1. Press the On/Off button (.	15
2. Hold down the function key # and press the Start button P until the display 8 indicates •:‹x or š:‹x (x can be any number). Release both buttons.	15
3. Press the function key # until the display 8 shows §:‹†.	15
4. Press the function key 3 to select the desired setting.	15
5. Press the Start button P to save the setting.	15
Turning off rinse aid indicator	16
NOTICE	16
- Loading the Dishwasher	16
Loading the Dishwasher	16
Dishware material	16
Note:	16
Recommended	16
Not Recommended	16
Glass and silverware damage	17
Causes:	17
Recommendation:	17
Loading the racks	17
For best dishwashing results, observe the following when loading the dishwasher:	17
NOTICE	17
Loading the upper rack	17
Note:	17
Loading the lower rack	17
Recommended loading pattern	18
12 place setting	18
Lower rack 9\	18
Upper rack 12	18
Note:	18
Third rack 1*	18
Additional loading pattern	18
10 place setting	18
Lower rack 9\	18
Upper rack 12	18
Note:	18
Third rack 1*	19
Loading the silverware basket	19
9 WARNING	19
Risk of injury!	19
Unloading the dishwasher	19
9 CAUTION	19
Note:	19
Adjusting the height of the rack	20
With silverware basket	20
Upper rack	20
Lower rack	20
9.4 in (24 cm)	20
13.4 in (34 cm)	20
10.4 in (26.5 cm)	20
12 in (30.5 cm)	20
11.4 in (29 cm)	20
11 in (28 cm)	20
With third rack	20
Upper rack	20
Lower rack	20
7 in (18 cm)	20
13.4 in (34 cm)	20
8 in (20.5 cm)	20
12 in (30.5 cm)	20
9 in (23 cm)	20
11 in (28 cm)	20
RackMatic®	20
1. Pull the upper rack out of the dishwasher until it stops.	20
2. To lower the rack, push the RackMatic® lever inward.	20
3. To raise the rack, hold the basket on the sides of the upper rack and lift it up.	20
Note:	20
Rack accessories	21
Flip tines*	21
Third rack *	21
Plastic item clips *	22
Vase holder *	22
Cup shelves *	22
Removing/Installing third rack	23
Removing third rack 1*	23
1. Pull out third rack all the way (1).	23
2. Lift upper rollers over the stopper hooks of both rails (2).	23
3. Pull third rack out forward and upward so that the holding hooks and the lower rollers of the rack slide over the stopper hooks of both rails (3).	23
Installing third rack 1*	23
1. Pull out third rack rails all the way (1).	23
2. Insert third rack at an angle. Make sure that the stopper hooks of both rails slide in between the holding hooks and the lower rollers of the third rack (2).	23
3. Slide third rack in and lift the upper rollers over the front stopper hooks of both rails (3).	23
4. Push in third rack (4).	23
Removing/Installing upper rack with Rackmatic®	24
Removing upper rack 12	24
1. Pull out upper rack all the way (1).	24
2. Lift front rollers over the stopper hook of the rail (2).	24
3. Pull out upper rack forwards and upwards so that the upper and lower rollers of the rack slide over the stopper hooks of both rails (3).	24
Installing upper rack 12	24
1. Pull out upper rack rails all the way (1).	24
2. Insert upper rack at an angle. Make sure that the stopper hooks of both rails slide in between the upper and lower rollers on the rear side of the rack (2).	24
3. Slide upper rack in and lift the upper rollers over the front stopper hooks of both rails (3).	24
4. Push in upper rack (4).	24
. Detergent	25
Detergent	25
NOTICE	25
Note:	25
Wash Cycle	25
Hard Water/ Heavy Soil	25
Medium Water/ Medium Soil	25
Soft Water/ Little Soil	25
Adding detergent	26
1. If the detergent dispenser 92 is still closed, push the button 9: to open it.	26
Note:	26
2. When using detergent tabs, lay them such that they do not come in contact with the cover, insert a detergent tab flat, not on its side.	26
Note:	26
3. Close the lid by placing the finger on the lid as shown. Slide the lid closed until it clicks.	26
Tip:	26
/ Dishwasher Cycles	27
Dishwasher Cycles	27
Wash cycle	27
Recommended use	27
Possible wash cycle option	27
Note:	27
Note:	27
The Energy Guide label was based on the Normal soil sensing cycle as follows: The unit was tested without any rinse aid (liquid) in the rinse aid dispenser 9*. A single dose of detergent was inserted into the detergent dispenser 92, with no detergent...	27
0 Dishwasher Cycle Options	28
Dishwasher Cycle Options	28
Delay	28
Half Load *	28
Delicate	28
Sanitize	28
Extra Shine® *	28
Wash Cycle Information	29
Note:	30
Only sanitizing cycles have been designed to meet the requirements of Section 6 of the NSF/ANSI Standard for Residential Equipment for soil removal and sanitization efficacy. There is no intention, either directly or indirectly, to imply that all cyc...	30
1 Operating the Dishwasher	30
Operating the Dishwasher	30
9 WARNING	30
Risk of injury!	30
Protection against unintentional operation	30
This function will be activated when:	30
Note:	30
AquaSensor	31
Switching the appliance on	31
1. Turn the water supply on fully.	31
2. Press the On/Off button (.	31
3. Press Start button P.	31
Note:	31
Time display	31
Delay start	31
To set Delay start:	31
1. Press On/Off button (. Select a cycle.	31
2. Press Delay button @ until the displayed time corresponds with your requirements.	31
3. Press Start button P to activate Delay start.	31
To cancel Delay start:	31
1. Press Delay button @ until œ:‹‹ is indicated on the digital display 8.	31
2. Press Start button P to save setting.	31
Note:	31
Wash cycle end	32
Auto power off	32
To change the setting:	32
1. Press the On/Off button (.	32
2. Hold down the function key # and press the Start button P until the display 8 indicates š:‹x (x can be any number).	32
3. Release both buttons.	32
4. Press the function key # until the display 8 indicates ˜:‹x.	32
5. Press the function key 3 until the display corresponds with your requirements.	32
6. Press the Start button P.	32
Switching off the appliance	32
Short time after the end of the wash cycle:	32
1. Press On/Off button (.	32
2. Remove the dishes when they have cooled down.	32
9 WARNING	32
Risk of injury!	32
Interrupting the wash cycle	33
9 CAUTION	33
1. Press On/Off button (.	33
2. To continue the wash cycle, close the door and press On/Off button ( again.	33
Note:	33
Terminating the wash cycle (Reset)	33
Terminating the wash cycle	33
1. Press and hold Start button P for approximately 3 seconds until the display reads ‹:‹‚.	33
2. Wait about 1 minute while the dishwasher drains.	33
3. Press On/Off button (.	33
Changing the wash cycle	33
Child Lock (panel lock)	33
To set the panel lock:	33
1. Start the desired wash cycle.	33
2. Hold down the button with the / symbol over it for approximately 3 seconds until the display reads ’–.	33
’– will be indicated now if any button is pressed and the program will not be reset.	33
Intensive drying	34
1. Press the On/Off button (.	34
2. Hold down function key # and press Start button P until the display 8 indicates š:x (x can be any number).	34
3. Release both buttons.	34
4. Press function key # until the display 8 indicates the factory set value š:‹‹.	34
5. Press function key 3 to switch the intensive drying feature on š:‹‚ or off š:‹‹.	34
6. Press Start button P to save setting.	34
2 Care and Maintenance	34
Care and Maintenance	34
Cleaning the dishwasher	34
NOTICE	35
9 WARNING	35
Filters	35
Filter components	35
The filter system 1b consists of three parts.	35
Cleaning intervals	36
Your filter system may need to be cleaned when:	36
Cleaning interval	36
Use this setting,	36
Note:	36
To check or clean the filter system:	36
1. Unscrew the Large Object Trap as illustrated and remove the entire filter system.	36
2. Remove the microfilter from the fine filter for easier cleaning.	36
3. Rinse the filters under running water and use a soft brush to clean.	36
Note:	36
4. Reinstall the filter system in reverse sequence and lock into place by screwing the Large Object Trap until the marking arrows align.	36
Spray arms	37
Check spray arms 1:, 1R for grease and limescale deposits. If you find such deposits:	37
Drain pump	37
Large food remnants in the rinsing water not retained by the filters may block the waste water pump. In this case:	37
Note:	37
Preparing your unit for vacation	38
NOTICE	38
Winterizing your unit	38
NOTICE	38
3 Troubleshooting	39
Troubleshooting	39
Fault	39
Cause	39
Remedial action	39
Note:	42
4 Customer Service	48
Customer Service	48
1. Call us at 1-800-944-2904	48
2. Contact Customer Service from our web site: www.bosch-home.com/us or www.bosch-home.ca	48
3. Contact your installer or the Bosch Authorized Service Contractor in your area.	48
4. Write us:	48
‡ Statement of Limited Product Warranty	49
Statement of Limited Product Warranty	49
What this Warranty Covers & Who it Applies to:	49
The limited warranty provided by BSH Home Appliances Corporation (BSH) in this Statement of Limited Product Warranty applies only to Bosch® dishwashers (“Product”) sold to you, the first using purchaser, provided that the Product was purchased a...	49
How Long the Warranty Lasts	49
Extended Limited Warranty	50
BSH also provides these additional limited warranties:	50
Repair/Replace as Your Exclusive Remedy	50
Out of Warranty Product	51
Warranty Exclusions	51
The warranty coverage described herein excludes all defects or damage that are not the direct fault of BSH, including without limitation, one or more of the following:	51
How to Obtain Warranty Service	52
Table des matières	53
fr-ca Notice d'utilisation	53
( Indications de sécurité 55	53
( CONSIGNES DE SÉCURITÉ IMPORTANTES 56	53
ƒ Causes de pannes 60	53
* Mise en marche 61	53
+ Système d'adoucissement de l'eau / sels 64	53
, Produit de rinçage 66	53
- Chargement du lave-vaisselle 68	53
. Détergent 77	53
/ Cycles du lave-vaisselle 79	53
0 Options de cycles du lave-vaisselle 80	53
1 Mise en marche du lave-vaisselle 83	53
2 Entretien et maintenance 88	53
3 Dépannage 93	53
4 Service à la clientèle 103	53
‡ Déclaration de la garantie limitée du produit 104	53
( Indications de sécurité	55
Indications de sécurité	55
9 AVERTISSEMENT	55
9 ATTENTION	55
AVIS	55
Remarque :	55
( CONSIGNES DE SÉCURITÉ IMPORTANTES	56
CONSIGNES DE SÉCURITÉ IMPORTANTES	56
LISEZ ET CONSERVEZ CES INSTRUCTIONS	56
Pour réduire le risque d'incendie, de choc électrique, ou de blessures graves, respectez les consignes suivantes :	56
Risque d'incendie, de choc électrique, ou de blessures graves	56
9 AVERTISSEMENT	56
Risque de blessure ou de décès !	56
9 AVERTISSEMENT	56
Risque de blessures !	56
9 AVERTISSEMENT	56
Risque de choc électrique ou d'incendie !	56
9 AVERTISSEMENT	57
Risque pour la santè !	57
INSTRUCTIONS DE MISE À LA TERRE	57
9 AVERTISSEMENT	57
Risque de choc électrique !	57
Fonctionnement normal	58
9 ATTENTION	58
9 AVERTISSEMENT	58
Risque de blessures !	58
Sécurité pour enfants	59
Entretien et maintenance corrects	59
9 AVERTISSEMENT	59
Risque d’explosion !	59
Remarque :	59
AVIS	59
Avertissement issue de la proposition 65 de l’État de la Californie :	59
9 AVERTISSEMENT	59
ƒ Causes de pannes	60
Causes de pannes	60
AVIS	60
* Mise en marche	61
Mise en route	61
Vue d'ensemble de l'appareil	61
Panneau de commande	62
Remarque :	62
Composants internes du lave-vaisselle	62
Indicateurs	62
Réglages	63
Réglage	63
Réglages d'usine	63
Description	63
+ Système d'adoucissement de l'eau / sels	64
Système d'adoucissement de l'eau / sels	64
Tableau de dureté de l'eau	64
Réglage du système d'adoucissement de l'eau	64
Réglez le système d'adoucissement comme suit :	64
1. Demandez le degré de dureté de votre eau courante à votre fournisseur d'eau ou utilizer la bandelette d’analyse.	64
2. Le réglage à effectuer se trouve dans le tableau de dureté de l'eau.	64
3. Appuyez sur le bouton On/Off (Marche/Arrêt) (.	64
4. Maintenez la touche # enfoncée et appuyez sur le bouton Start (Démarrer) P jusqu'à ce que l'afficheur8 indique •:‹x (x peut être un nombre quelconque).	64
5. Relâchez les deux boutons. L'indicateur de la touche # clignote et l'afficheur 8 indique la •:‹‹. Appuyez sur la touche de fonction 3 pour sélectionner la valeur désirée.	64
6. Appuyez sur le bouton Start (Démarrer) P pour enregistrer le réglage.	64
Utilisation de sels spéciaux pour lave-vaisselle	65
AVIS	65
Remplissez les sels au maximum comme suit :	65
1. Retirez le bouchon à vis du distributeur 1Z.	65
2. Remplissez le distributeur d'eau (opération requise uniquement lors de la première mise sous tension de l'appareil).	65
3. Ajoutez le sel comme illustré (n'utilisez pas de sel de table, de comprimés de sel ni de sel destiné aux adoucisseurs d'eau de toute la maison).	65
Utilisation de détergents chargés en sels	65
Détergent chargé en sels	65
Éteindre l'indicateur de niveau bas de sels/le système d'adoucissement de l'eau	65
Éteindre le système d'adoucissement de l'eau	65
, Produit de rinçage	66
Produit de rinçage	66
Remarque :	66
Ajout de produit de rinçage	66
AVIS	66
1. Ouvrez le distributeur de liquide de rinçage 9* en appuyant sur le loquet du couvercle et en tirant celui-ci.	66
2. Ajoutez le produit de rinçage liquide au distributeur 9* à pleine capacité.Ne le remplissez pas outre mesure. Évitez tout déversement dans le trou d'aération.	66
3. Fermez le couvercle. Le couvercle doit être hermétiquement fermé jusqu'à l'encliquetage du loquet, pour garantir son étanchéité.	66
4. Essuyez tout excédent de produit de rinçage déversé lorsque le réservoir est plein.	66
Conseil :	66
AVIS	66
Réglage de la quantité de produit de rinçage utilisé	67
Paramètre	67
Quantité	67
1. Appuyez sur le bouton On/Off (Marche/Arrêt) (.	67
2. Maintenez la touche enfoncée # et appuyez sur le bouton Start (Démarrer) P jusqu'à ce que l'afficheur 8 indique •:‹x ou š:‹x (x peut être un nombre quelconque). Relâchez les deux boutons.	67
3. Appuyez sur la touche de fonction # jusqu'à ce que l'afficheur 8 indique §:‹†.	67
4. Appuyez sur la touche de fonction 3 pour sélectionner la valeur désirée.	67
5. Appuyez sur le bouton Start (Démarrer) P pour enregistrer le paramètre.	67
Désactivation de l'indicateur de produit de rinçage	67
AVIS	67
- Chargement du lave-vaisselle	68
Chargement du lave-vaisselle	68
Matériaux lavables au lave-vaisselle	68
Remarque :	68
Recommandé	68
Non recommandé	68
Dégâts causés à la verrerie et l'argenterie	69
Causes :	69
Recommandations :	69
Chargement des paniers	69
Pour obtenir les meilleurs résultats, respectez les instructions suivantes lors du chargement de la vaisselle :	69
AVIS	69
Chargement du panier supérieur	69
Remarque :	69
Chargement du panier inférieur	69
Mode de chargement recommandé	70
Réglage 12 places	70
Panier inférieur 9\	70
Panier supérieur 12	70
Remarque :	70
Troisième panier 1*	70
Configuration de chargement supplémentaire	70
Réglage 10 places	70
Panier inférieur 9\	70
Panier supérieur 12	70
Remarque :	71
Troisième panier 1*	71
Chargement du panier à ustensiles	71
9 AVERTISSEMENT	71
Risque de blessures !	71
Retrait de la vaisselle	72
9 ATTENTION	72
Remarque :	72
Réglage de la hauteur du panier	72
Avec le panier à ustensiles	72
Panier supérieur	72
Panier inférieur	72
24 cm (9,4 po)	72
34 cm (13,4 po)	72
26,5 cm (10,4 po)	72
30,5 cm (12 po)	72
29 cm (11,4 po)	72
28 cm (11 po)	72
Avec le troisième panier	72
Panier supérieur	72
Panier inférieur	72
18 cm (7 po)	72
34 cm (13,4 po)	72
20,5 cm (8 po)	72
30,5 cm (12 po)	72
23 cm (9 po)	72
28 cm (11 po)	72
RackMatic®	73
1. Faites sortir le panier supérieur du lave-vaisselle jusqu'à la butée.	73
2. Pour abaisser le panier, poussez le levier RackMatic® lever vers l'intérieur.	73
3. Pour relever le panier, tenez les côtés du panier supérieur et soulevez-le.	73
Remarque :	73

Match case Limit results 1 per page

Operating the Dishwasher

en-us

Interrupting the wash cycle

CAUTION

Expansion (overpressure) may

cause the appliance door to

open and/or water to escape! If

the door was opened on an

appliance which has a hot water

connection or is heated, always

leave the door ajar for several

minutes and then close.

Press

On/Off

button

(

The LED’s go out. The wash cycle

is saved.

To continue the wash cycle, close

the door and press

On/Off

button

(

again.

Note:

Your dishwasher is protected

against unintentional operation. If the

appliance door remains open for

more than 4 seconds after pressing

the Start button, the operation will be

paused. Close the appliance door

and press the Start button

again.

Terminating the wash cycle

(Reset)

Te r m

nati

the

wash

cycl

Press and hold

Start

button

for approximately 3 seconds until

the display reads

‹

‹‚

Wait about 1 minute while the

dishwasher drains.

Press

On/Off

button

(

You may now power the dishwasher

back on and begin a new cycle if

desired.

Changing the wash cycle

When the

Start

button

(

has been

pressed, the wash cycle cannot be

changed. The only way a wash cycle

can be changed is by terminating the

wash cycle (Reset).

Child Lock (panel lock)

The child lock will lock the panel

while the dishwasher is in operation

to prevent that a wash cycle is

interrupted unintenionally (e.g. by

children).

To set the panel lock:

Start the desired wash cycle.

Hold down the button with the

symbol over it for approximately

3 seconds until the display reads

’–

The panel lock is active.

’–

will be indicated now if any button

is pressed and the program will not

be reset.

deactivate

the panel lock hold

down the button with the

over it for

approximately 3 seconds until the

display no longer reads

’–

The panel lock is deactivated

automatically when the wash cycle is

completed. In case of a power

outage the panel lock will remain

active. The panel lock has to be

activated with each new wash cycle.