Bosch SHV7ER53UC Instructions for Use - Page 15
Operating the Dishwasher - panel
View all Bosch SHV7ER53UC manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
Operating the Dishwasher Start the dishwasher 1 Open the door and press the [On/Off] button. The LED of the last selected cycle flashes. 2 Select a cycle and desired options. 3 Press [Start] and close the door to begin the cycle. Cancel a cycle 1 Open the door just far enough to expose the control panel. Be careful of hot water that may splash out. 2 Press and hold the [Start] button for approximately 3 seconds until the display reads "0:01". 3 Close the door and wait about 1 minute while the dishwasher drains. 4 Open the door and press the [On/Off] button. Interrupt a cycle 1 Open the door just far enough to expose the control panel. Be careful of hot water that may splash out. 2 Press the [On/Off] button to turn the unit off. 3 To resume the cycle, press the On/Off button and close the dishwasher door. Setting the amount of rinse aid The amount of rinse aid dispensed can be set from "r:00" to "r:06". To change the setting: 1 Open the door and press the [On/Off] button. 2 Hold down the "A" button (see page 4) and press [Start] until the display indicates "H:00". 3 Release both buttons. 4 Press the "A" button until the display shows "r:05". 5 Press the "C" button to select the desired setting. "r:00" = dispenser is OFF "r:01" = lowest setting "r:02" = low setting "r:03" = medium setting "r:04" = medium/high setting "r:05" = high setting "r:06" = highest setting 6 Press [Start] to save the setting and close the door. InfoLight An LED illuminates the floor to indicate the unit is running. If the appliance is installed at eye-level, the LED is not visible. To change the setting: 1 Open the door and press the [On/Off] button. 2 Hold down the "A" button (see page 4) and press [Start] until the display indicates "H:00". 3 Release both buttons. 4 Press the "A" button until the display shows "1:01". 5 Press the "C" button to switch between "1:01" = ON and "1:00" = OFF and press [Start] to save. Delay Start You can delay the start of the cycle in one hour increments up to 24 hours. To set delay start: 1 Open the door and press the [On/Off] button. 2 Press the [+] button until the display jumps to "h:01". 3 Press the [+] or [-] button until the displayed time corresponds with your requirements. h:01 = 1 hour delay h:24 = 24 hour delay 4 Press [Start] to activate delay start. To cancel delay start: 1 Press the [+] or [-] button until "h:00" is indicated on the digital display. 2 Press [Start] to save setting and close the door. 13
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64