Bosch SHX4AP05UC Use and Care Manual - Page 19

Operating the Dishwasher - and does not drain

Get Bosch SHX4AP05UC - Ascenta 24inch Built PDF manuals and user guides
UPC - 825225878735
View all Bosch SHX4AP05UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Operating the Dishwasher SHE5AL To start the dishwasher: • Door must be closed. Press the "ON/OFF" button. • One of the Wash Cycle LEDs will be lashing. You can now select a wash cycle. • Press the "" button to select the desired wash cycle. • Select the "Half Load" or "Delay Start" features if desired at this point. In addition to your Wash Cycle selection, for small loads of lightly soiled dishes press the "Half Load" button. This will save energy and water. If you would like to delay the start time of the dishwasher press the "DELAY" button until the desired delay time (3,6,9 hrs.) is displayed by the corresponding LED. • Press the "START" button to begin the cycle (Wash Cycle Indicator Light will stop lashing) • Press the "START" button (LED stops lashing) NOTE: Rinse Agent Indicator Light will be illuminated if the unit needs Rinse Agent. Child Lock • After pressing the "START" button you can activate the Child Lock feature. • Press and hold down the "" button. • The "Clean" and one other LED will be lashing. You are now in the options setup mode. • Press ">" to select the option you would like to adjust. If the "Clean" and "Rinse Agent" LED are lashing you can adjust the Rinse Agent settings. If the "Clean" and "Sanitized" LED are lashing you can set the Extra Dry Heat. To set the amount of Rinse Agent: NOTE: If your glasses have spots on them, you need more rinse agent. If your glasses have streaks, you need less Rinse Agent. Follow the prior instructions to enter "options" mode. With the "Clean" and "Rinse Agent" LED lashing: • Press the "

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
19
To start the dishwasher:
Door must be closed. Press the “ON/OFF” button.
•
One of the Wash Cycle LEDs will be ³ashing. You can
•
now select a wash cycle.
Press the "<" or ">" button to select the desired wash
•
cycle.
Select the "Half Load" or "Delay Start" features if
•
desired at this point.
±n addition to your Wash Cycle selection, for small loads of
lightly soiled dishes press the “Half Load” button. This will
save energy and water.
±f you would like to delay the start time of the dishwasher
press the “DELAY” button until the
desired delay time
(3,6,9 hrs.) is displayed by the corresponding LED.
Press the “START” button to begin the cycle (Wash
•
Cycle ±ndicator Light will stop ³ashing)
Press the “START” button (LED stops ³ashing)
•
NOTE: Rinse Agent ±ndicator Light will be illuminated if
the unit needs Rinse Agent.
Child Lock
After pressing the “START” button you can activate
•
the Child Lock feature.
Press and hold down the “<” button until Child Lock
•
LED illuminates (Light goes out when button is
released).
Now any button you press (except ON/OFF) will not
•
function and the Child Lock LED illuminates when
you press any button.
To deactivate, press and hold the “<” button until the
•
Child Lock LED goes out.
To cancel a cycle:
Press and hold the “START/RESET” button until the
•
"Active" LED goes out.
Wait for about 1 minute until the dishwasher drains.
•
Press the “ON/OFF” button.
•
The "Clean" indicator light will illuminate.
•
You are now ready to start a new cycle.
•
•
To enter the options mode(rinse agent setting, extra
dry heat, cycle completion signal):
Door must be closed. Press the "ON/OFF" button to
•
turn the unit on.
One of the Wash Cycle LEDs will be ³ashing.
•
Press and hold down the ">" button, then press and
•
release the "START/RESET" button. Now release the
">" button.
The "Clean" and one other LED will be ³ashing. You
•
are now in the options setup mode.
Press ">" to select the option you would like to
•
adjust.
±f the "Clean" and "Rinse Agent" LED are ³ashing you can
adjust the Rinse Agent settings.
±f the "Clean" and "Sanitized" LED are ³ashing you can set
the Extra Dry Heat.
To set the amount of Rinse Agent:
NOTE:
±f your glasses have spots on them, you need more
rinse agent. ±f your glasses have streaks, you need less
Rinse Agent.
Follow the prior instructions to enter "options" mode.
With the
"Clean" and "Rinse Agent" LED ³ashing
:
Press the "<" button to change the amount of rinse
•
agent dispensed.
0 LEDs ±ashing --> Rinse Agent dispenser is OFF
1 LED
±ashing --> Lowest amount of rinse agent
2 LEDs ±ashing --> Medium amount dispensed
3 LEDs ±ashing --> Highest amount of rinse agent
Press
•
START
to save your settings.
To turn Extra Dry Heat on or o²:
With the
"Clean" and "Sanitized" LED ³ashing
:
Press the "<" button to turn Extra Dry Heat on or o².
•
0
0 LEDs ±ashing --> Extra Dry Heat is OFF
1 LED ±ashing --> Extra Dry Heat is ON
Press
•
START
to save your settings.
Operating the Dishwasher
SHE5AL