Bosch SHX68R56UC Instructions for Use - Page 14
Wash Cycle Information, Operating the Dishwasher
View all Bosch SHX68R56UC manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
Wash Cycle Information Note: To save energy, this dishwasher has a "Smart Control" where the sensors in the dishwasher automatically adjust the cycle length, temperature and water changes based on the amount of food soil and the incoming water temperature. The "Smart Control" makes decisions that can cause the cycle time and water usage to adjust intermittently. Wash cycle times are based on 120°F water supply. If your household water supply is higher than 120°F, your dish- washer's heating time may be reduced and the "Sanitized" light or symbol may not illuminate. Table 2 - Wash Cycle Information Heavy Wash Auto Wash Normal Wash Delicate Wash Express Wash Rinse & Hold cycle time 135 min 95-119 min 115 min 80 min 30 min 9 min cycle time with Half Load 115 min 99 min 90 min not available not available not available cycle time with Sanitize 135 min 105-135 min 125 min not available not available not available water consumption 23.2-27.4 L 6.1-7.2 gal 10.4-22.5 L 2.7-5.9 gal 8.9-18.3L 2.4-4.8 gal 13.1 L 3.5 gal 13.1 L 3.5 gal 4.7 L 1.2 gal wash temperature 66-72°C 151-162°F 55-72°C 126-162°F 50-69°C 122-156°F 50°C 122°F 45-72°C 113-162°F no wash rinse temperature 72°C 162°F 65-72°C 156-162°F 45-69°C 113-156°F 69°C 156°F 50°C 122°F incoming water temp. Note: Only sanitizing cycles have been designed to meet the requirements of 6 for soil removal and sanitization efficacy. There is no intention, either directly or indirectly, that all cycles have passed sanitization performance tests. Operating the Dishwasher Start the dishwasher: 1 Open the door and press the On/Off button. 2 Select a cycle and desired options. 3 Close the door to begin the cycle. Delay start: 1 Open the door and press the On/Off button. 2 Select a cycle. 3 Press and hold the Delay Start button. Release when the desired delay time is shown in the dis- play window. 4 Close the door to begin the cycle. Cancel a cycle: 1 Open the dishwasher door just far enough to expose the control panel. Be careful of hot water that may splash out. 2 Press and hold the two buttons labeled Cancel/Reset for 3 seconds. 3 Close the door and wait about 1 minute while the dishwasher drains. 4 Open the door and press the On/Off button. You may now start a new cycle. WARNING You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR CAREFULLY during any wash or rinse cycle. Do not fully open the door until water noises have stopped. Interrupt a cycle: 1 Open the dishwasher door just far enough to expose the control panel. Be careful of hot water that may splash out. 2 Press the On/Off button to turn the unit off. 3 Wait at least 10 seconds before fully opening the dishwasher door. 4 To resume the cycle, press the On/Off button and close the dishwasher door. 12
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64