Bosch WTVC6530UC Operating Guide - Page 10

reinstalling - 10

Page 10 highlights

5. Rotate the door so that it is perpendicular to the dryer front. Slide the door away from the dryer so the hinge pins slide out of the grooves in the dryer door. striker Rotate the cover glass 90 degrees clockwise. 9. Remove the single screw that was hidden by the striker plate cover. 14. Note the new position of the cover glass. The leading edge of the raised glass edge should have moved 90 degrees clockwise from its starting point as shown in the illustration below as (A). check to make sure that all four plastic bushings remain on the hinge pins 10. Remove the four screws holding the front ring to the door body. Avoid allowing the 4 plastic bushings to fall off the hinge pins. If any of the bushings do fall off, reinstall them on the hinge pins prior to reinstalling the door. 6. Lay the dryer door face down on a firm, flat, padded surface, with the bottom of the door facing towards you. 7. Remove the single screw that was hidden by the hinge cover plate. 11. Flip the door over so the front ring faces up. 12. Remove the front ring from the dryer door. 15. Rotate the front ring 180 degrees so the door handle is now on the right hand side. The door handle is located on the inside of the front ring. It is a hand-sized indent. 8. Remove the two screws holding the striker cover plate in place. Hold the striker while lifting the cover so as to keep the parts together in place and set the assembly aside for later reinstallation. 10 13. The cover glass has a raised glass edge that goes about two-thirds of the way around the glass. Be sure this raised edge faces up towards you. Observe the position of the leading edge of the raised glass handle, marked in the illustration below as (A). 16. Flip the door over so the back faces up. 17. Reassemble the parts, preserving their new alignments.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104

10
5.
Rotate
the
door
so
that
it
is
perpendicular
to
the
dryer
front.
Slide
the
door
away
from
the
dryer
so
the
hinge
pins
slide
out
of
the
grooves
in
the
dryer
door.
check
to
make
sure
that
all
four
plastic
bushings
remain
on
the
hinge
pins
Avoid
allowing
the
4
plastic
bushings
to
fall
off
the
hinge
pins.
If
any
of
the
bushings
do
fall
off,
reinstall
them
on
the
hinge
pins
prior
to
reinstalling
the
door.
6.
Lay
the
dryer
door
face
down
on
a
firm,
flat,
padded
surface,
with
the
bottom
of
the
door
facing
towards
you.
7.
Remove
the
single
screw
that
was
hidden
by
the
hinge
cover
plate.
8.
Remove
the
two
screws
holding
the
striker
cover
plate
in
place.
Hold
the
striker
while
lifting
the
cover
so
as
to
keep
the
parts
together
in
place
and
set
the
assembly
aside
for
later
reinstallation.
striker
9.
Remove
the
single
screw
that
was
hidden
by
the
striker
plate
cover.
10.
Remove
the
four
screws
holding
the
front
ring
to
the
door
body.
11.
Flip
the
door
over
so
the
front
ring
faces
up.
12.
Remove
the
front
ring
from
the
dryer
door.
13.
The
cover
glass
has
a
raised
glass
edge
that
goes
about
two-thirds
of
the
way
around
the
glass.
Be
sure
this
raised
edge
faces
up
towards
you.
Observe
the
position
of
the
leading
edge
of
the
raised
glass
handle,
marked
in
the
illustration
below
as
(A).
Rotate
the
cover
glass
90
degrees
clockwise.
14.
Note
the
new
position
of
the
cover
glass.
The
leading
edge
of
the
raised
glass
edge
should
have
moved
90
degrees
clockwise
from
its
starting
point
as
shown
in
the
illustration
below
as
(A).
15.
Rotate
the
front
ring
180
degrees
so
the
door
handle
is
now
on
the
right
hand
side.
The
door
handle
is
located
on
the
inside
of
the
front
ring.
It
is
a
hand-sized
indent.
16.
Flip
the
door
over
so
the
back
faces
up.
17.
Reassemble
the
parts,
preserving
their
new
alignments.