Boss Audio BG200 User Manual in English - Page 8

Specifications, BG200, Generator, Troubleshooting

Get Boss Audio BG200 PDF manuals and user guides View all Boss Audio BG200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Specifications BG200 Bass Generator Powerfullow frequency enhancement system forbass afficianados 3053 AUDIO SYSTEMS Input voltage level Output voltage level Frequency response THD Signal-to-noise ratio Balanced input noise rejection Input impedance Output impedance Power supply type Fuse rating All specifications subject to change without notice. 15V rms 10V peak (maximum) 10Hz - 100kHz (+/- dB) 0.003% 130dB >60dB 10 k-ohm 150 ohms PMW 1A Troubleshooting If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous pages. If problems persist, read the following troubleshooting tips which may help eliminate the problems. SYMPTOM POSSIBLE REMEDY Unit will not power up. Check that Battery (+) and Ground connections are not reversed. Check that all wires are properly connected and that adequate voltage (11-16V) is present. Check that fuse is not blown. Sound is very distorted. Check that input level and output level are set correctly. Input level should match the output of the source unit, and output level should match the sensitivity of the audio unit connected to the Bass Generator's outputs. Volume level is very low. Check that input level and output level are set correctly. Input level should match the output of the source unit, and output level should match the sensitivity of the audio unit connected to the Bass Generator's outputs. Engine noise (alternator whine) Verify that the ground connection is secure, near the unit, and uses a heavy gauge wire. Check that the Battery (+) wire is not unnecessarily long. Try connecting to power from a different point in the vehicle. BG200 User's Manual - page 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
Specifications
3053
BG200
Bass
Generator
Powerful
low
frequency
enhancement
system
for
bass
afficianados
AUDIO
SYSTEMS
Input
voltage
level
15V
rms
Output
voltage
level
10V
peak
(maximum)
Frequency
response
10Hz
-
100kHz
(+/-
dB)
THD
0.003%
Signal-to-noise
ratio
130dB
Balanced
input
noise
rejection
>60dB
Input
impedance
10
k
-ohm
Output
impedance
150
ohms
Power
supply
type
PMW
Fuse
rating
1A
All
specifications
subject
to
change
without
notice.
Troubleshooting
If
you
experience
operation
or
performance
problems
with
this
product,
compare
your
installation
with
the
electrical
wiring
diagram
on
the
previous
pages.
If
problems
persist,
read
the
following
troubleshooting
tips
which
may
help
eliminate
the
problems.
SYMPTOM
POSSIBLE
REMEDY
Unit
will
not
power
up.
Check
that
Battery
(+)
and
Ground
connections
are
not
reversed.
Check
that
all
wires
are
properly
connected
and
that
adequate
voltage
(11-16V)
is
present.
Check
that
fuse
is
not
blown.
Sound
is
very
distorted.
Check
that
input
level
and
output
level
are
set
correctly.
Input
level
should
match
the
output
of
the
source
unit,
and
output
level
should
match
the
sensitivity
of
the
audio
unit
connected
to
the
Bass
Generator's
outputs.
Volume
level
is
very
low.
Check
that
input
level
and
output
level
are
set
correctly.
Input
level
should
match
the
output
of
the
source
unit,
and
output
level
should
match
the
sensitivity
of
the
audio
unit
connected
to
the
Bass
Generator's
outputs.
Engine
noise
(alternator
whine)
Verify
that
the
ground
connection
is
secure,
near
the
unit,
and
uses
a
heavy
gauge
wire.
Check
that
the
Battery
(+)
wire
is
not
unnecessarily
long.
Try
connecting
to
power
from
a
different
point
in
the
vehicle.
BG200
User's
Manual
-
page
8