Boss Audio BRRC14 User Manual - Page 1

THIS PACKAGE CONTAINS

1 - BRRC14 Soundbar Speaker System

1 - Bluetooth Multi-Function Controller Kit

1 - 1.50” Rollbar Mounting Kit

1 - 1.75” / 2.00” Rollbar Mounting Kit

1 - Quick Connect Power Cable

1 - User Manual Quick Start Guide / Poster

1 - Warranty Card / Facebook Card

FCC

COMPLIANCE STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause

undesired operation of this device.

This transmitter must not be co-located or operated in conjunction with any other

antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by

user. This equipment complies with FCC/ IC radiation exposure limits set forth for

an uncontrolled environment and meets the FCC radio frequency (RF) Exposure

Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This

equipment has very low levels of RF energy that it deemed to comply without

maximum permissive exposure evaluation (MPE). But it is desirable that it should

be installed and operated keeping the radiator at least 20 cm or more away from

person’s body (excluding extremities: hands, wrists, feet and ankles). Alteration

or modifications carried out without appropriate authorization may invalidate the

user’s right to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-

signed to provide reasonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guar-

antee that

interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

□ Relocate or reorient the receiving antenna.

□ Increase the separation between the equipment and receiver.

□ Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

□ Consult the dealer or an experienced radio/TV technician for help.

USER MANUAL

QUICK START GUIDE

Thank you for purchasing this

BRRC14 Soundbar Sound System

Please read through these instructions carefully so you will know

how to operate your model properly.

After you have finished reading the instructions, keep this document

in a safe place for future reference.

INFORMATION TO THE USER

INFORMATION TO THE USER

T

he Bluetooth® word mark and logos are registered trademarks owned by

Bluetooth SIG, Inc. and any use of such marks is under license.

Other trademarks and trade names are those of their respective owners.

CAUTION!!

ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

GETTING TO KNOW YOUR

BRRC14 MULTIFUNCTION CONTROLLER (MFC)

BEFORE YOU START

IMPORTANT SAFETY PRECAUTIONS

■

Do not operate mobile equipment while driving a motorized vehicle – safe driving and

safety consideration of others should always be your highest priority

■

In the event you should notice smoke, strange noises or odor from this product, or any

other abnormal signs, immediately turn off the power and consult your dealer or the nearest

authorized

BOSS AUDIO

Service Center. Using this product in this condition may result in

permanent damage to the system

■

Set your volume control at a low setting, then slowly increase the sound until you can

hear it comfortably without distortion, or ear discomfort

■

BE SURE TO OBSERVE THE FOLLOWING GUIDELINES

:

- Do not turn up the volume so high that you can’t hear what’s around you

- Use caution or temporarily discontinue use in potentially hazardous situations

INSTALLATION PRECAUTIONS

WARNING

- Always consult a professional installer

■

Do not attempt to install or service this product by yourself. Installation or servicing of this

product by persons without professional training and experience in electronic equipment

and motorized vehicle accessories may be dangerous and could expose you to the risk of

electric shock, injury or other hazards

■

Refer any repairs to a qualified

BOSS AUDIO SYSTEMS

Service Center

■

The

BRRC14

should be hard wired directly to the main vehicle battery

■

When wiring directly to the vehicles battery, be sure to disconnect the batteries negative

terminal wire before starting any wiring procedures

■

The ground cable length should be short as possible (See wiring diagram)

■

The

BRRC14

has a weather resistant design, it should not be under any circumstances

submerged in, or under water

■

Use only the supplied installation parts provided with the

BRRC14

■

Wash with a mild detergent and lukewarm water using a clean sponge or a soft cloth

■

Rinse well with clean water

“DO NOT’S” - Very Important

■

DON’T clean in hot sun or on very hot days

■

DON’T use abrasive or highly alkaline cleaners on the main body

■

DON’T scrape the main body with razor blades, or other sharp instruments

■

DON’T ever use, gasoline, acetone or carbon tetrachloride

■

DON’T ever use a pressure washer aimed at the speakers

GETTING STARTED

A

1

2

3

4

5

6

7

8

9

8

7

4

2

3

A

MFC - MULTIFUNCTION CONTROLLER

DOME LIGHT ON/OFF -

(Auto 10 minute timer when MFC ACC is turned OFF)

POWER ON/OFF

- Press and hold for 3 seconds

LOUDNESS ON/OFF -

Single Press

NEXT TRACK -

FF press and hold

PLAY/PAUSE -

AUX MUTE

BLUETOOTH PAIRING INDICATOR LED

- BLUE

/ AUX RED COLOR

PREVIOUS TRACK -

FR press and hold

VOLUME DOWN -

Ramp DOWN press and hold

VOLUME UP -

Ramp UP press and hold

CAUTION!! Using other mounting methods may void this warranty

PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION

1) Power on the

MFC

by long-pressing the

3

Power button

for 3 seconds, long-press the

6

Bluetooth

button for 3 seconds, the

BLUE LED

will start to rapidly flash, signalling that

the

MFC

is now ready for

Bluetooth

pairing

NOTE:

You have 2 minutes before you must restart this procedure over again.

2) The

MFC

is now in pairing mode:

ANDROID users:

a. Go into the

Settings Menu

of your device

b. Enter the

Bluetooth Menu

c.

TURN ON Bluetooth

and press

SCAN

d.

“BOSS REBEL UTV”

will now be displayed under

AVAILABLE DEVICES

e. If prompted, enter passcode: “

0000

”

iOS users:

a. Go into the

Settings Menu

of your

iOS

device

b. Enter the

Bluetooth Menu

c

. TURN ON Bluetooth

d.


will now be displayed

e. If prompted, enter passcode: “

0000

”

3) If

BOSS REBEL UTV

is not seen, repeat the above steps to refresh the “

Device List”

4) When the connection is successful a tone will be heard, and the

Bluetooth

LED indicator

will light solid, you are now ready to stream music from your favorite media player to the

MFC

Using this product without running the engine can drain the battery.

To avoid battery exhaustion, be sure to occasionally run the

vehicles engine while using this product.

BLUETOOTH OPERATION

STREAMING MUSIC

RECONNECTION

1) Power on the

MFC

and your last paired device Bluetooth.

2) Ensure you are within range of the

MFC

, the unit will now automatically reconnect

3) If the device is out of range from the

MFC

, it will disconnect automatically:

a. The

MFC

will reconnect automatically to your device when in range

4) If your device was previously paired with the

MFC

, but it wasn’t the last paired device:

a. Ensure no other devices are currently paired

b. Enter the

Bluetooth Menu

on your device being paired

c.


will display under

AVAILABLE DEVICES

d. Choose the


to reconnect

5) To clear all previously paired devices from memory, press and hold the

MFC Bluetooth

button for 10 seconds

NOTE:

Some devices may require a manual

Bluetooth

reconnection once the devices

Bluetooth

is powered

OFF / ON

and/or back in range, repress the

BOSS REBEL UTV

button in BLUETOOTH settings on your device

3

Tips:

MULTIFUNCTION CONTROLLER BLUETOOTH OPERATION

1) Press the

5

PLAY/PAUSE

once to start playing music or press the

PLAY

button from

your devices touch screen

2) To skip songs or advance, press the

4

NEXT TRACK

button

3) To select the previous song, press the

7

PREVIOUS TRACK

button

VOLUME CONTROL

4) To raise the volume press the

9

VOLUME UP

button or use your devices controls

5) To lower the volume press the

8

VOLUME DOWN

button or use your devices controls

NOTE:

If

BLUETOOTH

or

AUX

is disconnected for more than 10 minutes the

MFC

will

automatically turn

OFF

, however, when not in use the

ACC

switch should be manually

turned

OFF

to keep the vehicles main battery from draining

MULTIFUNCTION CONTROLLER AUX-IN OPERATION

1) Power on the

MFC

by pressing and holding down the

3

POWER

button for 3 seconds

2) Disconnect any paired

Bluetooth

device by turning off

Bluetooth

in your devices

Settings Menu

3) Connect your 3.5mm

AUX-IN

cable located on front side of the

MFC

to your devices

headphone jack

4) Route the wire back to

MFC

, secure your device in a safe location

VOLUME CONTROL

5) To raise the volume press the

9

VOLUME UP

button

6) To lower the volume press the

8

VOLUME DOWN

button

7) To

MUTE

the volume press the

5

PLAY/PAUSE

button

AUX-INPUT

Make sure your device Bluetooth volume is set at 100% level

before stowing your device

BEFORE YOU START INSTALLATION

Make sure your device headphone volume is set at 100% level

before stowing your device

MFC

can play audio from

any device that has a 3.5mm

headphone audio jack.

INSERT

(Cable not included)

YOUR

DEVICE

Tips:

Tips:

MULTI-FUNCTION CONTROLLER MOUNTING

TOOLS NEEDED:

- Crimp Tool

- Wrench or Pliers

- 3mm Allen Wrench

MOUNTING THE SOUNDBAR

When replacing the fuse, be sure to only use a fuse of the rating specified on

this product. To avoid short-circuiting, cover any disconnected leads with insulating

tape. It is especially important to insulate any unused wires, which if left uncovered

may cause a short circuit. When connecting other devices to this product, refer to

the manual for the product to be connected. The black cable is ground, make sure

to connect the ground wire first. Ensure that the ground wire is properly connected

to metal parts of the vehicles body frame or direct to the battery if your vehicle

does not have a grounded chassis frame The ground wire of this units power amp

and a second powered system must be connected to the frame separately with

different screws. If the screw for the ground wire loosens or falls out, it could result

in fire or malfunction.

To avoid potential shorts in the electrical

system, be sure to disconnect the (–)

battery cable before installation. Use this

unit with a 12-Volt battery and negative

grounding only. Failure to do so may result

in a fire or malfunction.

BRRC14

RECOIL SERIES

BLUETOOTH

®

| 14” AMPLIFIED SOUNDBAR SYSTEM

USER’S MANUAL

QUICK START GUIDE

BRRC14

USER’S MANUAL

RECOIL SERIES

14” AMPLIFIED SOUNDBAR SOUND SYSTEM

WITH BLUETOOTH REMOTE CONTROLLER

PRINTED IN CHINA

VER:1.1 EN

iPod / iPhone are trademarks of Apple Inc. registered in the U.S. and other countries

Android is a trademarks of Google Inc. registered in the U.S. and other countries.

BOSS Audio Systems is not affiliated with Apple Inc. or Google Inc.

317

BOSS Audio Systems

3451 Lunar Court • Oxnard, CA 93030

www.bossaudio.com

|

805-322-8794

Tech Support: www.bossaudio.com/support/technical-support

BLUETOOTH

• Version: 4.1

• A2DP / AVRCP / GATT

• Range: 33ft (10m) Class 2

• Loudness EQ

• RCA Line Output: 2V RMS

SPEAKERS

• Dimension: 3.0”

• Cone Type: PP CARBON

• Tweeter Size: 1”

SOFT DOME

AMPLIFIER

• Maximum Output Power: 300 Watts

• Input Impedance: 10kΩ

• Frequency Response: 45Hz-25kHz

GENERAL

• Operational Power: 14.4VDC (10-16V allowable)

• MAX Current Draw: 6.7A

• USB Charging: 1A @ 5VDC +/- 5%

• Replacement Fuse: 15A ATO TYPE

• Cabinet Material: Aluminum Extrusion

• Color: Black Powder Coating

SPECIFICATIONS

WIRE DIAGRAM

Dimensions:

14.02" (356mm) x 4.98" (126.5mm) x 5.55" (141mm)

Weight:

9.92 lbs (4.5 kg)

5.55"

(141mm)

14.02"

(356mm)

4.98"

(126.5mm)

15A

Fuse and fuse holder

Chassis

ground

point

BATTERY

Replace with 15A only

INSERT

DIRECT BATTERY WIRING CIRCUIT

RED

BLACK

Chassis

ground

point

MFC

Ground wire

Metal frame

( AUX Cable not included)

INSERT

RED

BLACK

ACC SWITCH

LINE OUT

(-) ORANGE

(+) BLUE

DOME LIGHT

AMP REMOTE INPUT

RIGHT

LEFT

GROUND

CRIMP

DAISY CHAIN

LINE OUTPUTS

LINE IN

(-) MOMENTARY TO ACTIVATE

3A

• Weight: 9.92lbs / 4.5kg

• Dimensions Inches WxHxD: 14.02 x 4.98 x 5.55

• Dimensions cm WxHxD: 35.6 x 12.6 x 14.1

• Storage Temperature: 5

o

F to 175

o

F

/ -15

o

C to 80

o

C

• Operation Temperature: 32

o

F to 140

o

F / 0

o

C to 60

o

C

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including

photocopying, recording, or other electronic or mechanical methods, without the prior written permission of BOSS AUDIO Inc.

Copyright © 2017 BOSS AUDIO Inc.

BLUETOOTH OPERATION

CAUTION!!

Mounting brackets should be periodically checked to be sure they are tight

and secure before use of the vehicle.

9

3.5mm AUX-INPUT

CABLE NOT INCLUDED

USB 1A

CHARGING

NOT FOR AUDIO PLAYBACK

OPEN

ALWAYS CLOSE COVER WHEN

NOT IN USE NEVER USE WHEN

IN MUD and/or WATER

1

5

6

6

7

4

5

8

9

5

8

9

3

1) Determine the size

rollbar

for your vehicle, install rubber

bushings

on

rollbar

2) Insert and align notch of

rubber bushings

into the

aluminum brackets

3) Apply supplied

Loc-Tight

to

allen bolt

tips, let dry for 20 minutes, then align

the

allen bolts

and

T-nuts

into the

T-channel

, firmly tighten

4) Recheck all

allen bolts

are tight, ensure

T-nut’s

are properly seated in the

T-channel

correctly

Your Rollbar

Rubber Bushing

Rubber Bushing

INSTALLATION PARTS

1.5”

1.75”

2”

RUBBER BUSHINGS

1.5”

1.75” or 2”

BRACKETS

ROLLBAR / CAGE MOUNT

ALIGN CONNECTOR

PINS, INSERT and

HAND TIGHTEN

1.5”

1.75”

2.00”

FLUSH MOUNT

SURFACE MOUNT

NEVER CONNECT +12V

TO THE DOME WIRE

LED DOME - ON/OFF

MUTE - ON/OFF

STATUS INDICATOR

WHITE = ON

RED = STANDBY

CAUTION:

NEVER CONNECT THE

MFC

DIRECTLY

TO THE BATTERY, ALWAYS USE AN

ACCESSORY SWITCH

CAUTION!!

Never use

USB

or

AUX

while in

mud and/or water

Close USB cover

when not in use

ONBOARD CONTROL PANEL

Some applications may require

optional friction tape between

rubber bushings for a secure,

tight fit, this can be found at

most local hardware stores

1) Always check mounting depth before cutting

2) Use the flush bezel as template

3) Cutout hole exactly

4) Insert flush mount bezel, push side tabs outwards

5) Use optional silicon glue to give extra hold

6) Insert

MFC

1) Check mounting depth before drilling

2) Use the flush bezel as template

3) Drill or cut wire hole exactly

4) Insert rubber trim around flush bezel,

screw in place

5) Insert

MFC

MFC can rotate 90

o

for the

best mounting position

3mm Allen Head

3mm Allen Head

T-nut must be assembled

in this configuration

Align notch

Align notch

OPTIONAL

OPTIONAL

OPTIONAL TOOLS NEEDED:

- Hand saw or Jigsaw

NOTE!!

To conserve battery life, the LED Dome light will automatically turn off after

10 minutes when MFC ACC is turned OFF

BOSS REFLEX SERIES

OPTIONAL SYSTEM

EXPANSIBILITY

MFC RESET

LONG PRESS BOSS

LOGO FOR 10 SECONDS

Boss Audio BRRC14 User Manual - Page 1

Boss Audio BRRC14 Manual

Page 1 highlights