Boss Audio BX25 User Manual in English - Page 2
switching, power, Features, specifications, subject, change, without, notice., LEVELS, MIDRANGE,
View all Boss Audio BX25 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
INTRODUCTION Congratulations on your purchase of a BOSS Audio Systems Electronic Crossover. This product has been designed and built to deliver excellent sound quality and long lasting high performance. We are sure you'll enjoy listening to your favorite music with this BOSS component in your car audio system. For best results please consult a professional car stereo installer for application advice or troubleshooting. To guarantee top performance we recommend using The BOSS Link installation accessories such as RCA interconnects. power cable, and speaker wire. Thank you for choosing BOSS Audio Systems products for your autosound system. We can't change the world. but we can make it sound better. FEATURES HIGH PASS CHANNEL : High Pass Frequency Selector 50Hz to 1.5KHz High Pass Output Level Control SUBWOOFER CHANNEL Low Pass Frequency Selector 35Hz to 400Hz +12dB Bass Boost Phase Shift Switch Stereo:Mono Switch Output Level Sontrol Exclusive Remote Subwoofer Level Control SPECIFICATIONS Power Supply StN Ratio Channel Separation Distortion Crossover Slope Input Impedance Output Impedance ..... Output Gain Output Voltage Level DC to DC switching power liodt3 80dB THD L 0 01% 12dB per Octave 20K Ohms 100 Ohms 1:2 (+6dB) Waits Max Dimensions (W x L X H): 8-3/4"X 5-3/4" x 1-112" (222mm x 146mm x 38mm) Features arid specifications subject to change without notice. CONTROLS AND OPERATION 13 LJ 41106-S_O ARKOKB•,....K4y NUM 2 6 •=12.11 .f 5 14 12 1. Low Level Input jacks. 1. Subwoofer Low Pass Frequency Selector: By turning the selector you can choose from an infinite number of crossover points from 35Hz to 400Hz. 2. Bass Boost Control (45Hz): You can increase the bass level up to +12dB. 3. Phase Shift Selector Switch: Use this switch to select Output Phase for the Subwoofer Channel to provide best lime alignment and stereo imaging. 4. High Pass Frequency Selector: By turning the selector you can choose from an infinite number of crossover points from 50Hz to1.5KHz. 5. Subwoofer Output Level Control: By turning this control clockwise you can increase Low pass output gain. 6. Stereo/Mono Switch: For selection of stereo or mono mode for Subwoofer Output Signal. 7. High Pass Output Level Control: By turning this control clockwise you can increase the High pass output gain. 8. LED Power On Indicator. 9. Signal Input Connectors 10. Low Pass (Sub-Woofer) Output Connectors 11. High Pass Output Connectors 12. Power Connections Terminal: +12V, Ground arid Remote Turn-On INSTALLATION 1 Find a suitable location in the vehicle to mount the crossover. 2 Bolt the crossover to the mounting surface3. Using the screw terminals provided, conned! minimum 16 gauge wire from the power, Ground and remote terminals. Connect the shortest possible wire to a chassis ground point The (+)12V connection should be made directly to the car battery, and the remote should be connected to the Remote Turn On Lead of your head unit. When connecting directly to the battery, install a 3A Fuse within 18 inches of the battery terminal. 4. Connect all line Inputs and outputs using high-quality RCA cables. 5. Recheck all connections before powering up. 6. Set all level controls to their minimum positions and set all crossover controls, switches, etc. To the desired frequency or position. 7. Once the system is powered up, set the volume control on the head unit to a moderate level where your normal speaking voice can be heard while the music is playing. 8 Further fine tuning of the various controls may be necessary to obtain the desired results. 9 When unsure about installation or system tuning, please consult an authorized BOSS AUDIO dealer. ELECTRONIC CONNECTIONS & WIRING Power connection • B4(12V) Connect a red wire to the car battery Of other power source. • REMOTE Connect an orange wire to remote activating (12V DC)wire of car stereo or equalizer, • GND Connect a black wire lo the car chassis for ground connection_ BLA K POD GRANGE + BATTERY 2 L WIRING DIAGRAM: Signal Connection This is typical 2-way connection. In this mode the output signal will he deviled into two: LOW PASS and HIGH PASS output terminals. Connect HIGH PASS output to an amplifier for composite signal of HIGH range and connect LOW PASS output to LOW (SUB-WOOFER) amplifier. Refer to the following illustration. REMOTE CONTROL (Low PASS LEVELS O6SO biNKEVILO 044,NYS ,orn..v. CAR STEREO E a CrCi CI ED+ 2 POWER AMPLIFIER 'MID-SASS 'MIDRANGE 'TWEETER i=7 POWER AMPLIFIER SUE-WOOFER