Boss Audio CPBL3.5 User Manual in English - Page 5

CAUTION, stereo, power, turned, capacitor, display, However, capacitor, still, powerful, charge,

Get Boss Audio CPBL3.5 PDF manuals and user guides View all Boss Audio CPBL3.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Power-up procedures After installing the capacitor according the directions on the previous page, follow these instructions for powering up and charging the capacitor. This procedure is extremely important to perform, and eliminates the possibility of damaging the capacitor, battery and other audio devices. I WATTIS1 OHM RESISTOR (supplied) Do not hold the resistor as it can get and cause bums! GROUND CABLE 1. Connect the ground cable to the capacitor (-) terminal. CABLE FROM BATTERY (+) POSITIVE 2. Temporarily attach the resistor supplied with the capacitor to the power cable, using electrical tape to secure the connection. Charging the capacitor 3. SEE FIGURE 2 (AT RIGHT). Holding the power cable securely, place the free end of the resistor on the (+) terminal of the capacitor. While this is occurring, the status LED will be illuminated, and the red decimal point will flicker, indicating that the system is charging the capacitor. - DECRIAL POINT rockers during charging EEO When the capacitor is fully charged, the decimal point will no longer flicker, and the display will show the DC voltage of the car charging system. 4. Remove the tape, detach the resistor from the power cable, and attach the power cable securely to the (+) capacitor terminal. 5. Put the resistor in a safe storage location, as you will need it in the future when you need to discharge the capacitor. Digital display features - 3-DIGIT VOLTAGE DISMAY Displays the DC voltage (Amur cat charging system STATUS LED This indicator flashes when the capacitor is charging CAUTION! When you turn off your car stereo, power is turned off to the capacitor, and its display will turn off. However, the capacitor may still hold a powerful charge, so always treat it as if it is powered ON even 4 if the display is OFF!

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
Power
-up
procedures
After
installing
the
capacitor
according
the
directions
on
the
previous
page,
follow
these
instructions
for
powering
up
and
charging
the
capacitor.
This
procedure
is
extremely
important
to
perform,
and
eliminates
the
possibility
of
damaging
the
capacitor,
battery
and other
audio
devices.
1.
Connect
the
ground
cable
to
the
capacitor
(-)
terminal.
2.
Temporarily
attach
the
resistor
supplied
with
the
capacitor
to
the
power
cable,
using
electrical
tape
to
secure
the
connection.
3.
SEE
FIGURE
2
(AT
RIGHT).
Holding
the
power
cable
securely,
place
the
free
end
of
the
resistor
on
the
(+)
terminal
of
the
capacitor.
While
this
is
occurring,
the
status
LED
will
be
illuminated,
and
the
red
decimal
point
will
flicker,
indicating
that
the
system
is
charging
the
capacitor.
When
the
capacitor
is
fully
charged,
the
decimal
point
will
no
longer
flicker,
and
the
display
will
show
the
DC
voltage
of
the
car
charging
system.
4.
Remove
the
tape,
detach
the
resistor
from
the
power
cable,
and
attach
the
power
cable
securely
to
the
(+)
capacitor
terminal.
5.
Put
the
resistor
in
a
safe
storage
location,
as
you
will
need
it
in
the
future
when
you
need
to
discharge
the
capacitor.
4
I
WATTIS1
OHM
RESISTOR
(supplied)
Do
not
hold
the
resistor
as
it
can
get
and
cause
bums!
GROUND
CABLE
CABLE
FROM
BATTERY
(+)
POSITIVE
Charging
the
capacitor
—
DECRIAL
POINT
ro
ckers
during
charging
EEO
Digital
display
features
—
3
-DIGIT
VOLTAGE
DISMAY
Displays
the
DC
voltage
(Amur
cat
charging
system
STATUS
LED
This
indicator
flashes
when
the
capacitor
is
charging
CAUTION!
When
you
turn
off
your
car
stereo,
power
is
turned
off
to
the
capacitor,
and
its
display
will
turn
off.
However,
the
capacitor
may
still
hold
a
powerful
charge,
so
always
treat
it
as
if
it
is
powered
ON
even
if
the
display
is
OFF!