Bowflex Elite Assembly and Owners Manual - Page 16

Step 18 - Attach the Rod Box Frame to the Lat Tower, Step 19 - Attach the Faceplate to the Main - power rods

Get Bowflex Elite PDF manuals and user guides View all Bowflex Elite manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Assembly Guide Step 18 - Attach the Rod Box Frame to the Lat Tower Locate the following items: • From Step 16 - Main Assembly • From Step 17 - Rod Box/Frame Assembly • Item #K - (2) 3/8" X 5" Button Head Screws • Item #N - (4) 3/8" Washers • Item #O - (2) 3/8" Nylock Nuts Align the bolt holes on the Rod Box brackets with the bolt holes on the Lat Tower above the Chest Bar , as shown in Figure 18. Figure 18 K N Rod Box Brackets Place (2) 3/8" Washers (Item #N) over the ends of (2) 3/8" X 5" Button Head Screws (Item #K) - one washer per screw. Insert the screws through the aligned holes. Place (1) 3/8" Washer and (1) 3/8" Nylock Nut (Item #O) over the Chest Bar end of each screw and tighten. O Completely tighten hardware installed during Step 18. Step 19 - Attach the Faceplate to the Main Assembly Locate the following items: • Item #26 - Faceplate • From Step 18 - Main Assembly • Item #A - (2) #10 Phillips Head Screws Figure 19 Faceplate "Stems" Position the textured side of the Faceplate (Item #26) against the Lower Lat Tower. Insert the plastic "stems" through the corresponding holes on the Lower Lat Tower, as shown in Figure 19. You may need to push the Power Rods® out of the way to 26 insert the screws into the holes. Attach the Faceplate to the Lower Lat Tower by threading (2) #10 Phillips Head Screws (Item #A) into the "stems". A Do not completely tighten hardware installed during Step 19 tighten screws approximately 1/2 of completion. Hardware will be tightened during Step 20. A-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
A-14
Step 18 - Attach the Rod Box Frame to the Lat Tower
Locate the following items:
• From
Step 16
-
Main Assembly
• From
Step 17
- Rod Box/Frame Assembly
•
Item #K
- (2) 3/8" X 5" Button Head Screws
•
Item #N
- (4) 3/8" Washers
•
Item #O
- (2) 3/8" Nylock Nuts
Align the bolt holes on the Rod Box brackets with the bolt
holes on the Lat Tower above the Chest Bar , as shown in
Figure 18
.
Place (2) 3/8" Washers (Item #N) over the ends of
(2) 3/8" X 5" Button Head Screws (Item #K) - one washer
per screw. Insert the screws through the aligned holes. Place
(1) 3/8" Washer and (1) 3/8" Nylock Nut (Item #O) over the
end of each screw and tighten.
Completely tighten hardware installed during Step 18.
Step 19 - Attach the Faceplate to the Main Assembly
Locate the following items:
•
Item #26
- Faceplate
• From
Step 18
- Main Assembly
•
Item #A
- (2) #10 Phillips Head Screws
Position the textured side of the Faceplate (Item #26) against
the Lower Lat Tower.
Insert the plastic “stems” through the
corresponding holes on the Lower Lat Tower, as shown in
Figure
19
. You may need to push the Power Rods® out of the way to
insert the screws into the holes.
Attach the Faceplate to the Lower Lat Tower by threading
(2) #10 Phillips Head Screws (Item #A) into the “stems”.
Do not completely tighten hardware installed during Step 19 -
tighten screws approximately 1/2 of completion. Hardware will
be tightened during Step 20.
Figure 18
O
N
Rod Box
Brackets
Chest Bar
K
Figure 19
A
26
Faceplate
“Stems”
Assembly Guide